MFJ-1270C/1274C MANUAL APPENDIX G: SUMMARY
Page 250
COMMAND SUMMARY
Command Parameter Default Mode Function Page
8BITCONV ON|OFF on Packet Enables transmission of 8 bit data in converse mode 6-5
ABORT -- I-command M-Packet Allows SYSOP to force a disconnect on the Mailbox
link
6-6
ACKPRIORITY ON|OFF on Packet Permits an acknowledging TNC to transmit without
regard to slotting delay
6-7
ACKTIME n 14 Packet Controls a delay that occurs whenever any packets that
have been received are not addressed to that unit
6-7
ANSWRQRA ON|OFF on Packet Set MFJ TNC to polls all TNCswithin range. 6-9
AUTOLF ON|OFF on Packet Determines the way the <CR>characters are displayed. 6-13
AWLEN n 8 All Defines the word length used by the MFJ TNC 's RS-
232 port.
6-14
AX25L2V2 ON|OFF on Packet Determines the use of AX.25 Level 2 Ver. 2 or Ver. 1
Protocol.
6-15
AXDELAY n 0 Packet Sets the voice repeater keyup delay in 10 ms intervals. 6-16
AXHANG n 0 Packet Sets the voice repeater hang time in 100 ms intervals. 6-17
BBSMSGS ON|OFF off Packet Controls the display of certain messages incommand
and CONVERS mode
6-18
BEACON n 0 Packet Sets the timing for an automatic transmission of a
packet.
6-19
BKONDEL ON|OFF on Packet Determines the way the screen is updated when a
character is deleted in the command mode.
6-20
BLP ON|OFF on Packet Allows Host Mode operation 6-21
BTEXT text blank Packet Specifies the text of the beacon packet. 6-22
BUDLIST ON|OFF off Packet Determines if the packets listed in LCALLS are to be
displayed.
6-23
CALIBRA -- I command All Used to transfer the control to the modem calibration
routine.
6-24
CANLINE n $18 (^x) Packet Changes the cancel-line input editing command
character.
6-26
CANPAC n $19 (^Y) Packet Changes the cancel-packet inputediting command
character.
6-27
CBELL ON|OFF off Packet Sends bell tone to computer or terminal speaker when a
packet connection is made.
6-28
CHAT -- I-command M-Packet Allows SYSOP to break onto the mailbox's connected
link.
6-29
CHECK n 30 Packet Sets a connection timeout. 6-29
CHECKV1 ON|OFF off Packet Enables the automatic idle-link-dis- connect feature for
AX.25 L2V1 connections.
6-30
CONPERM ON|OFF off Packet Allows a connection to become 6-30 permanent.
CMDTIME n 1 Packet Sets the transparent mode timeout value. 6-31
CMSG ON|OFF off Packet Enable a message to be transmitted whenever there is a
connection made.
6-32
CMSGDISC ON|OFF off Packet Controls whether the MFJ TNC will initiate a
disconnect sequence after it is connected to.
6-32
COMMAND n $03 (^C) All Sets the character used to enter the command mode
from CONVERS mode.
6-33
CONMODE C|T C Packet Sets the MFJ TNC to enter the transparent mode or
converse mode automatically.
6-34
CONNECT C1|Cx none Packet Issues a connect from the command mode to another
packet station.
6-35
CONOK ON|OFF on Packet Determines the action taken by the MFJ TNC when it
receives a connect request.
6-36
CONSTAMP ON|OFF off PacketEnables the time stamping when a disconnect
occurs.
6-37
CONVERS -- I-command All Forces the MFJ TNC to enter the converse mode. 6-37
CPACTIME ON|OFF off Packet Enables the automatic transmission of packets in the
converse mode.
6-38
CR ON|OFF on Packet Causes the MFJ TNC to send a <CR>every time a
new line character is sent.
6-39
CTEXT text blank Packet Determines the packet text to be sent when a connect is
made.
6-40
CSTATUS -- I-command Packet Shows streams identifier and link state of all streams. 6-39
DAYTIME D/T none Packet Sets the time and date used by the MFJ TNC 6-43
To Next Page
