2016-2023 Microchip Technology Inc. DS50002489G-page 39
RN4870/71
11.0 REGULATORY APPROVAL
The RN4870 module has received the regulatory
approval for the following countries:
• United States/FCC ID: A8TBM70ABCDEFGH
• Canada/ISED
- IC: 12246A-BM70BLES1F2
- HVIN: BM70BLES1F2
• Europe/CE
• Japan/MIC: 202-SMD069
• Korea/KCC: MSIP-CRM-mcp-BM70BLES1FC2
• Taiwan/NCC No: CCAN15LP0501T3
• China/SRRC: CMIIT ID: 2016DJ5729
The RN4871 module has received the regulatory
approval for the following countries:
• United States/FCC ID: A8TBM71S2
• Canada/ISED
- IC: 12246A-BM71S2
- HVIN: BM71BLES1FC2
• Europe/CE
• Japan/MIC: 005-101150
• Korea/KCC: MSIP-CRM-mcp-BM71BLES1FC2
• Taiwan/NCC No: CCAN16LP0011T7
• China/SRRC: CMIIT ID: 2016DJ5890
• Brazil/ANATEL: 02699-19-08759
11.1 United States
The RN4870/71 module has received Federal Communi-
cations Commission (FCC) CFR47 Telecommunications,
Part 15 Subpart C “Intentional Radiators” single modular
approval in accordance with Part 15.212 Modular
Transmitter approval. Single modular transmitter
approval is defined as a complete RF transmission sub-
assembly, designed to be incorporated into another
device, that must demonstrate compliance with FCC rules
and policies independent of any host. A transmitter with a
modular grant can be installed in different end-use
products (referred to as a host, host product or host
device) by the grantee or other equipment manufacturer,
then the host product may not require additional testing,
or equipment authorization for the transmitter function
provided by that specific module or limited module device.
A host product itself is required to comply with all other
applicable FCC equipment authorization regulations,
requirements and equipment functions that are not
associated with the transmitter module portion. For
example, compliance must be demonstrated: to regula-
tions for other transmitter components within a host
product; to requirements for unintentional radiators
(Part 15 Subpart B), such as digital devices, computer
peripherals, radio receivers, etc.; and to additional
authorization requirements for the non-transmitter
functions on the transmitter module (i.e., Verification or
Declaration of Conformity) as appropriate (e.g.,
Bluetooth and Wi-Fi
®
transmitter modules may also
contain digital logic functions).
11.1.1 LABELING AND USER
INFORMATION REQUIREMENTS
The RN4870 module has been labeled with its own
FCC ID number, and if the FCC ID is not visible when
the module is installed inside another device, then the
outside of the finished product into which the module is
installed must also display a label referring to the
enclosed module. This exterior label can use wording
as follows:
For the RN4870 module:
Due to the limited size of the RN4871, the FCC Identifier
(FCC ID) is not displayed on the module. Therefore, the
FCC ID must be placed on the outside of the finished
product into which the module is installed and must
also display a label referring to the enclosed module.
This exterior label can use wording as follows:
For the RN4871 module:
Contains Transmitter Module
FCC ID: A8TBM70ABCDEFGH
or
Contains FCC ID: A8TBM70ABCDEFGH
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Contains Transmitter Module
FCC ID: A8TBM71S2
or
Contains FCC ID: A8TBM71S2
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Downloaded from Arrow.com.
To Next Page
Loading...
Need help?
General
