Microhard Systems pMDDL2450 - Page 102

© Microhard 102
5.0 AT Command Line Interface
Firewall AT Commands
AT Command Description Syntax Effect
AT+MFGEN Get/Set firewall general configuration AT+MFGEN[=<Config>[,<Mode>]]
Parameters
Config : 0 - WAN Remote Management
1 - WAN Request
2 - LAN to WAN Access Control
3 - Anti-Spoof
4 - Packet Normalization
Mode : 0 - Disable (Block)
1 - Enable (Allow)
AT&W
AT+MFDMZ Get/Set firewall DMZ configuration AT+MFDMZ[=<DMZ Source>[,<DMZ Mode>[,<DMZ Server IP>,<Exception Port>]]]
Parameters:
DMZ Source : 0 - WAN
DMZ Mode : 0 - Disable
1 - Enable
DMZ Server IP : Valid IP address
Exception Port : 0 - 65535
AT&W
AT+MFPORTFWD Get/Set firewall Port Forwarding rule AT+MFPORTFWD[=<Name>[,<Operation>[,<Source>,<Internal IP>,<Internal Port>,<Protocol>,
<External Port>,<SNAT>]]]
Parameters:
Name : Name of Port Forwarding rule, 1 - 64 characters
Operation : ADD - Add a rule
EDIT - Edit a rule
DEL - Delete a rule
Source : 0 - WAN
1 - USB
Internal IP : Valid IP address
Internal Port : Valid port number, 1 - 65535
Protocol : 0 - TCP
1 - UDP
2 - TCPUDP
External Port : Valid port number, 1 - 65535
Source NAT : 0 - No; 1 - Yes
Usage:
AT+MFPORTFWD
AT+MFPORTFWD=<Name>
AT+MFPORTFWD=<Name>,DEL
AT+MFPORTFWD=<Name>,ADD,<Source>,<Internal IP>,<Internal Port>,<Protocol>,<External
Port>,<SNAT>
AT+MFPORTFWD=<Name>,EDIT,<Source>,<Internal IP>,<Internal Port>,<Protocol>,<External
Port>,<SNAT>
AT&W
AT+MFMAC Get/Set firewall MAC list AT+MFMAC[=<Name>[,<Operation>[,<Action>,<Mac Address>]]]
Parameters:
Name : Name of firewall MAC list name, 1 - 64 characters
Operation : ADD - Add a firewall MAC list
EDIT - Edit a firewall MAC list
DEL - Delete a firewall MAC list
Action : 0 - Accept
1 - Drop
2 - Reject
MAC Address : Valid MAC address
Usage:
AT+MFMAC
AT+MFMAC=<Name>
AT+MFMAC=<Name>,DEL
AT+MFMAC=<Name>,ADD,<Action>,<Mac Address>
AT+MFMAC=<Name>,EDIT,<Action>,<Mac Address>
AT&W
AT+MFIP Get/SET firewall IP list AT+MFIP[=<Name>[,<Operation>[,<Action>,<Source>,<IP Address>[,<Prefix>]]]]
Parameters:
Name : Name of firewall IP list name, 1 - 64 characters
Operation : ADD - Add a firewall IP list
EDIT - Edit a firewall IP list
DEL - Delete a firewall IP list
Action : 0 - Accept
1 - Drop
2 - Reject
Source : 0 - LAN
1 - Independent LAN
2 - WAN
3 - USB
Source IP : Valid IP address
Prefix : 0 ~ 32. 32 (default) - single IP address
Usage:
AT+MFIP
AT+MFIP=<Name>
AT+MFIP=<Name>,DEL
AT+MFIP=<Name>,ADD,<Action>,<Source>,<IP Address>[,<Prefix>]
AT+MFIP=<Name>,EDIT,<Action>,<Source>,<IP Address>[,<Prefix>]
AT&W