DOC 6501_Release V
ATS-6501 Users Guide
62
226 Transfer complete (unique file name:tflex.tflex-5-2-2.iso).
10856448 bytes sent in 35.75Seconds 303.68Kbytes/sec.
ftp> quit
221 Goodbye.
3. Use the software_update <filename> command to update the software. When the
application launches, users should see the following information on the console as the
updater application run through the routine to update the system software.
6501_60>software_update tflex-5-2-2.iso
common_updater.sh: Invoked with command line: /updates/tflex-5-2-2.iso --noreboot
common_updater.sh: Extracting new updater from /updates/src/cpio-image.gz
common_updater.sh: New updater extracted, launching it now.
common_updater.sh: Invoked with command line: /updates/tflex-5-2-2.iso --noreboot --stage2
common_updater.sh: Stage 2 updater running
common_updater.sh: System is currently running from /dev/mmcsd0s1; applying updates to /dev/mmcsd0s2
common_updater.sh: Creating filesystem on /dev/mmcsd0s2a ..... ..... . done.
common_updater.sh: Creating filesystem on /dev/mmcsd0s2e ..... ..... . done.
common_updater.sh: Invoking product-specific pre-extract function
common_updater.sh: Preserving current syslog
common_updater.sh: Capturing data to be preserved across the update
common_updater.sh: Storing files ..... .... done.
common_updater.sh: Extracting updates from image file /updates/src/cpio-image.gz
common_updater.sh: Unpacking files ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... done.
common_updater.sh: Restoring overlay data to be preserved across the update
common_updater.sh: Unpacking files ..... .... done.
common_updater.sh: Editing new /etc/fstab to change /dev/mmcsd0s1 to /dev/mmcsd0s2
common_updater.sh: Invoking product-specific post-extract function
Sending command words: 0x03a50301 0x00000000
common_updater.sh: FPGA warmstart register has been cleared; a coldstart will occur
common_updater.sh: Cleaning up temporary files and flushing all data to disk
common_updater.sh: Setting bootable flag in partition 2
common_updater.sh: UPDATE SUCCESSFUL
Outputs disabled
Warm start successfully disabled
Rebooting...
[OK] 2013-08-05T15:17:53Z
4. Once the update is complete the system will automatically reboot. Local users will
see the front panel display lock up for ~2 minutes. After this the system will begin
launching the application and local users will see the typical boot process where the
bars repeatedly start off at the top, move to the middle, then bottom, then go out. The
application startup will take ~2 minutes. Once the oscillator lock light is on it should
take about 1 minute to begin tracking GPS and the front panel clock to come back. It
will take an additional 1.5 to 2 minutes for NTP to lock and for the outputs to be
enabled.
Note: Users can obtain the new software image and software release notes from Microsemi
ftp://ftp.timing.com/pub/ATS-6501. Refer to the software release notes for specific instructions
related to a particular revision of software. If the software update is not applied after transferring
the image to the unit and the unit is power cycled users will need to upload the .iso file again in
order to update the system software.
Warning: Users upgrading from software versions prior to Version 3.9.X will NOT be able to
use this command to update the software. This will require replacing the front panel flash card.
Caution: If the software update is not applied and the unit is power cycled users will need to
upload the .iso file again in order to update the system software. The .iso file will be wiped from
the system since it is held in volatile memory.
To Next Page
Loading...
