MicroStep-MIS MSB780 User Manual (English)

To Next Page

MSB780, MSB780X,

MSB780X transfer standard

Digital Barometers

Version 1.25

User’s Guide

October 17, 2017

Table of Contents4
Hardware13
Principle of Operation13
Terminals13
Power Supply13
Power Consumption - Model with Touchscreen Display13
Power Saving Mode15
Serial Interface (RS-232)15
Connecting MSB780 or MSB780X to PC16
Interface Wiring16
Service Connector16
MSB780X Transfer Standard Version17
Connecting the External Probe to the Transfer Standard19
Turning the Transfer Standard On/Off20
Recharging the Transfer Standard Battery20
Using the Transfer Standard with AA Batteries21
Connecting the Transfer Standard to a Computer21
Transfer Standard Connectors Description22
Adjustment of the Transfer Standard22
Terminals of the Transfer Standard23
Memory Card24
Maintenance25
Cleaning25
Error States25
Recommended Recalibration Interval25
Compensation Sensor Exchange Procedure26
Compensation Sensor - Maintenance26
Compensation Sensor FAQ27
Calibration and Adjustment28
How to Read the Current Correction Values28
Disabling the Correction28
Adjusting MSB780X with more than One Transducer29
One Pressure Point Adjustment29
Two Pressure Points Adjustment29
More than 2 Pressure Points Adjustment30
Caset" Adjust the Analog Output31
And RS-485 Commands32
Serial Interface Command Set32
Basic Commands34
P" Poll Measurement Command34
D" Poll Extended Measurement Command34
Cnf?" Print Configuration35
Errors" Print Error Message38
Sdi12A" SDI-12 Address Change38
Help" Display Help39
Boot" Restart Device39
Seri" Set Communication Settings for User39
Echo1" Enable Echo39
Echo0" Disable Echo40
Form" Change Output Message Format40
Form?" Get Actual Output Message Format42
Smode" Change the User Port Start-Up Operating Mode42
Smode?" Get Actual User Port Start-Up Operating Mode43
Intv" Change the Outputting Interval for RUN Mode43
Intv?" Get Actual the Outputting Interval for RUN Mode44
Avrg" Averaging Time44
Avrg?" Get Averaging Time44
Addr" Change the Address in POLL Mode45
Addr?" Get Actual Address in POLL Mode45
Open" Access to Command Mode in POLL Mode45
Close" Close Command Mode in POLL Mode45
Send" Read the Output Message in POLL Mode46
Unit" Change the Measurement Unit46
Unit?" Get Actual Measurement Unit47
Cnfdef" Set Default Configuration47
Terminal Rs232" Temporarily Redirect the Service Port to RS23247
Terminal Rs485" Temporarily Redirect the Service Port to48
Terminal Probe" Temporarily Redirect the Service Port to External Probe48
Dir E:" Print List of Files48
Type <Filename>" Print File49
Xmodemr - Downloading Files Using XMODEM49
Adjustment Commands50
Cset" Set Adjust Coefficients50
Cnf?" Get Actual Adjust Coefficients51
Dpmax" Set the Maximum Permissible Pressure Difference51
Dpmax?" Get the Maximum Permissible Pressure Difference51
Adjdef" Set Default Adjustment52
Corrected Pressure Commands - QFE, QNH, HCP52
Icaomode" Set Mode for Calculation of Corrected Pressures52
Icaodigits" Set Number of Decimal Praces of Corrected Pressures52
Hqfe" Set Altitude for QFE Corrected Pressure53
Hqnh" Set Altitude for QNH Corrected Pressure54
Tqfe" Set Temperature for QFE Corrected Pressure56
Tqfea" Set Actual Temperature for QFE Corrected Pressure56
Hhcp" Set Height Difference for HCP Level56
Hqfe?" Get Altitude for QFE Corrected Pressure57
Hqnh?" Get Altitude for QNH Corrected Pressure57
Tqfe?" Get Default Temperature for QFE Corrected Pressure57
Tqfea?" Get Actual Temperature for QFE Corrected Pressure57
Hhcp?" Get Height Difference for HCP Level57
Dt" Get Date and Time58
Setdt" Set Date and Time58
Setpin" Set New PIN Code58
Display Access59
Basic Screens59
Graph Screen61
Main Menu61
Menu Structure61
Recording Menu (Logging Data to SD Card, View in Graph)62
Measuring Menu (Measurement Settings)65
Interfaces Menu (Settings of Interfaces)68
System Menu (Date/Time, Diagnostics, Serial/Version Numbers)70
Display Menu (Shown Quantities, Graph Time-Scale, Backlight Settings)71
Alarm72
Reference73
Introduction to SDI-1273
Commands Supported by MSB78073
Commands Set74
A! Acknowledge Active Command74
Ai! Send Identification Command75
Address Query Command75
Aab! Address Change Command75
Am! Start Measurement Command75
Am1! Start Measurement Command, Return also HQFE, HQNH76
Ad0! Send Data Command76
Ar0! Continuous Measurement (Basic Units)76
Ar1! Continuous Measurement (User Units)77
Av! Get Verification77
Axd1! Send Data Command from Transducer77
Axv! Get Extended Verification78
Setting Parameters Via SDI-1279
Reading Parameters Via SDI-1279
Analog Output79
Amode" Set Analog Output Range80
Asel" Analog Output Quantity and Scale81
Atest" Analog Output Test82
Aerr" Analog Output Error Indication82
Technical Data83
Quantities83
Performance84
Analog Output Accuracy85
Operating Environmental85
Inputs and Outputs85
Power Consumption85
Drawings86
Troubleshooting90
In Case of Problems91
Ordering Information92
Firmware Update93
Hardware Required for Firmware Update93
Firmware Loader Software94
History of Changes99
1.199
1.299
1.2.199
1.2.299
1.2.399
1.2.499
1.3100
1.4100
1.5101
1.6101
1.7101
1.8101
1.9101
1.10101
1.11102
1.12102
1.13102
1.14102
1.15102
1.16102
1.17103
1.18103
1.19103
1.20103

Need help?

Do you have a question about the MicroStep-MIS MSB780 and is the answer not in the manual?

MicroStep-MIS MSB780 Specifications

General

Brand	MicroStep-MIS
Model	MSB780
Category	Weather Station
Language	English

Related product manuals

MicroStep-MIS MSB780X1D

104 pages

MicroStep-MIS MSB780 User Manual

Table of Contents

MicroStep-MIS MSB780 Specifications

Related product manuals