15
Installation
Instructions
-
-
Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors;
Saw (optional, to shorten window adaptor for narrow windows)
Tools Needed
Accessories
North America
Other Regions
NOTE: Items with (*) are on some models. Slight variations in design may occur.
Name of Accessories
Qty.
Shape
Name of Accessories
Qty.
Shape
1 pc(*)Window Slider A Bolt
1 pc 1 set(*)Unit Adaptor Security Bracket and 2 Screws
1 pc 1 pcExhaust Hose Drain Hose
1 pc(*) 1 pc
Window Slider Adaptor Power Cord Buckle
ON
/
O
FF
TE
M
P
S
H
O
R
T
CU
T
TIMER
O
N
T
I
M
E
R
OFF
M
O
D
E
FA
N
S
L
E
EP
S
W
ING
LED
1 set(*)1 pc(*)Window Slider B
Remote Controller and Battery
(only for remote control models)
1 pc(*)
Wall Exhaust Adaptor A
(only for wall installation models)
2 pc(*)Foam Seal A (Adhesive)
1 pc(*)
Wall Exhaust Adaptor B(with cap)
(only for wall installation models)
2 pc(*)Foam Seal B (Adhesive)
4 set(*)
Screw and anchor
(only for wall installation models)
1 pc(*)
Foam Seal C (Non-adhesive)
1 pc(*)
Drain Hose Adaptor
(only for heat pump mode)
1 pc(*)
1 pc(*)
1 pc(*)
Exhaust Hose Adaptor
Extended Exhaust Hose
1 set(*)Window Sliders
1 pc(*)Air exhaust passage
Name of Accessories
Qty.
Shape
Name of Accessories
Qty.
Shape
1 pcWindow Slider A Bolt
1 pc 1 setUnit Adaptor Security Bracket and 2 Screws
1 pc 1 pcExhaust Hose Drain Hose
1 pc
(on some models)
(on some models)
(on some models)
(on some models)
(on some models)
(on some models)
(on some models)
(on some models)
1 pc
Window Slider Adaptor Power Cord Buckle
O
N
/
O
F
F
TEMP
SH
OR
T
CUT
TIM
E
R
ON
TIMER
O
F
F
M
OD
E
FA
N
SL
E
EP
S
WI
NG
LED
1 set(*)1 pcWindow Slider B
Remote Controller and Battery
(only for remote control models)
1 pc(*)Window Slider C
2 pc/4 pc(*)
1 pc/2 pc(*)
Foam Seal A (Adhesive)
2 pc Foam Seal B (Adhesive)
1 pc/2 pc(*)
Foam Seal C (Non-adhesive)
1 pc(*)
Drain Hose Adaptor
(only for heat pump mode)
1 pc(*)
1 pc(*)
Exhaust Hose Adaptor
Extended Exhaust Hose
1 pc(*)Air exhaust passage
1 set(*)Window Sliders
This feature can be activated from the remote control
ONLY. To activate SLEEP feature, the set temperature
will increase(cooling) or decrease(heating) by 1°C/2°F
(or 1°F) in 30 minutes. The set temperature will then
increase(cooling) or decrease(heating) by another 1°C
/2°F (or 1°F) after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it
thermostat allowing for the precise temperature
control at its location. To activate the Follow Me/Temp
Sensing feature, point the remote control towards the
unit and press the Follow Me/Temp Sensing button.
The remote control will send this signal to the air
conditioner until press the Follow Me/Temp Sensing
button again. If the unit does not receive the Follow
Me/Temp Sensing signal during any 7 minutes interval,
the unit will exit the Follow Me/Temp Sensing mode.
To Next Page
Loading...
