MikroTik cAP XL ac User Manual

1.
cAP XL ac
cAP XL ac (RBcAPGi-5acD2nD-XL)
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.
Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an
uncontrolled environment.This MikroTik device should be installed and operated no closer than 20 centimeters from your body, occupational user, or the
general public.
Connecting
Connect POE to Ethernet port 1, please see the section for instructions on how to connect POE.Powering
Set your computer IP configuration to (DHCP). automatic
The device wireless access point mode is enabled by default.
The device will boot up and a Wireless network will be available for connecting.
Open network connections on your PC, mobile phone, or other device and search for MikroTik wireless network and connect to it.
Once connected to the wireless network, open in your web browser to start configuration, user name: admin, since there is https://192.168.88.1
no password by default, you will be logged in automatically .(or, for some models, check user and wireless passwords on the sticker)
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best
performance and stability.
Choose your country, apply country regulation settings, and set up your password on the screen that loads.
Powering
The device accepts power from the Ethernet port, so you must either use the included passive PoE injector or make sure your switch supports passive or
802.3af/at PoE output.
Ethernet port accepts 12-57 V DC (802.3af/at).
The power consumption under maximum load can reach 24 W.
Connecting to a POE Adapter:

MikroTik cAP XL ac Specifications

General

2.4 GHz	Yes
Frequency band	2 - 5.5 GHz
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3af, IEEE 802.3at
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Transmitting power (CE)	26 dBm
Maximum data transfer rate	867 Mbit/s
Mean time between failures (MTBF)	100000 h
Maximum data transfer rate (2.4 GHz)	300 Mbit/s
Security features	IPsec hardware acceleration
Security algorithms	-
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	2
Input current	1.2 A
AC input voltage	17 - 57 V
DC voltage range	24 V
Power consumption (max)	24 W
Power consumption (typical)	11 W
Power over Ethernet (PoE) type supported	Passive PoE
Placement	Ceiling, Wall
Product color	White
Antenna type	Internal
Chipset	IPQ-4018
Flash memory	128 MB
Internal memory	16 MB
Processor model	IPQ4018
Processor frequency	716 MHz
Operating system installed	RouterOS
Warranty period	5 year(s)
Sustainability certificates	CE, Federal Communications Commission (FCC), RoHS
Wireless technology	Wi-Fi 5

Weight and Dimensions

Width	191 mm
Height	42 mm