Mitsubishi QD75M1 User Manual

Index - 2
Allowable circular interpolation error width
(
Pr.41
)........................................................ 5-42
Amplifier setting (
Pr.101
)............................. 5-58
Analog monitor output (
Pr.122
)................... 5-68
Applicable system ........................................... 2-5
Applicable wire size......................................... 3-3
Arc address (
Da.7
)..................................... 5-92
Auto tuning (
Pr.108
) .................................... 5-62
Auto tuning (Explanation of positioning terms)
..........................................................Appendix-71
Automatic trapezoidal acceleration/deceleration
(Explanation of positioning terms) ... Appendix-71
Automatic trapezoidal acceleration/deceleration
processing method...................................... 12-81
Axis display LED ............................................. 4-3
Axis error No. (
Md.10
,
Md.23
)................ 5-116
Axis error occurrence (Hour) (
Md.11
)...... 5-116
Axis error occurrence (Minute: second) (
Md.12
)
..................................................................... 5-116
Axis error reset (
Cd.5
) ............................. 5-140
Axis feed rate (
Md.28
).............................. 5-124
Axis in which the error occurred (
Md.9
)
..................................................................... 5-116
Axis in which the warning occurred (
Md.14
)
..................................................................... 5-118
Axis monitor data......................................... 5-120
Axis operation status (
Md.26
) .................. 5-122
Axis stop signal ............................................. 3-18
Axis to be interpolated (
Da.5
).................... 5-84
Axis warning detection ................................ 5-126
Axis warning No. (
Md.15
,
Md.24
)........... 5-118
Axis warning occurrence (Hour) (
Md.16
). 5-118
Axis warning occurrence (Minute: second)
(
Md.17
)...................................................... 5-118
[B]
Backlash compensation amount (
Pr.11
). 5-28
Backlash compensation (Explanation of
positioning terms).............................Appendix-71
Backlash compensation function................ 12-11
Backup function (Explanation of positioning terms)
..........................................................Appendix-71
Ball screw (Explanation of positioning terms)
..........................................................Appendix-71
Basic parameters 1........................................5-22
Basic parameters 2........................................5-26
BCD (Explanation of positioning terms)
...........................................................Appendix-72
Bias speed at start (Explanation of positioning
terms) ................................................Appendix-72
BIN (Explanation of positioning terms)
...........................................................Appendix-72
Bipolar drive constant-current system (Explanation
of positioning terms) .........................Appendix-73
Block...............................................................10-2
Block No. being executed (
Md.45
)...........5-132
Block start (Normal start)...............................10-2
Block start data ..............................................10-7
Block start data area (Nos. 7000 to 7004)......7-3
Buffer memory .................................................7-2
Buffer memory (Explanation of positioning terms)
...........................................................Appendix-73
Buffer memory area configuration...................7-5
BUSY (Explanation of positioning terms)
...........................................................Appendix-73
BUSY signal...................................................3-12
[C]
Cable clamp ...................................................4-12
CCW (Explanation of positioning terms)
...........................................................Appendix-73
CHANGE signal (Explanation of positioning terms)
...........................................................Appendix-73
Circular interpolation (Explanation of positioning
terms) ................................................Appendix-73
Combination of functions...............................3-10
Combination of main functions and sub functions
........................................................................3-10
Command in-position flag............................5-126
Command in-position function.....................12-78
Command in-position width (
Pr.16
) ..........5-30
Command pulse (Explanation of positioning terms)
...........................................................Appendix-73
Command speed (
Da.8
).............................5-94
Common functions................................. 3-8, 13-2
Communicating signals between QD75 and each
module............................................................1-19
Composite speed...........................................5-32
Composite speed (Explanation of positioning
terms) ................................................Appendix-73

Mitsubishi QD75M1 Specifications

General

Brand	Mitsubishi
Model	QD75M1
Category	Controller
Language	English