Mitsubishi QD75M1 User Manual

Index - 11
Skip command (
Cd.37
)............................ 5-158
Skip function................................................ 12-61
Skip function (Explanation of positioning terms)
..........................................................Appendix-88
Skip operation program................................. 6-47
Slave axis (Explanation of positioning terms)
..........................................................Appendix-88
Slot................................................................... 2-5
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
Pr.13
)
....................................................................... 5-28
Software stroke limit selection (
Pr.14
)..... 5-28
Software stroke limit upper limit value (
Pr.12
)
....................................................................... 5-28
Software stroke limit valid/invalid setting (
Pr.15
)
....................................................................... 5-28
S-pattern acceleration/deceleration processing
method......................................................... 12-82
S-pattern proportion (
Pr.35
)...................... 5-38
Special start instruction (
Da.13
) .............. 5-101
Special start data instruction code setting value
(
Md.36
)...................................................... 5-130
Special start data instruction parameter setting
value (
Md.37
)............................................ 5-130
Special start repetition counter (
Md.41
)... 5-132
Specifications of input/output interfaces....... 3-16
Specifications of input/output signals ........... 3-12
Speed change (Explanation of positioning terms)
..........................................................Appendix-88
Speed change 0 flag ................................... 5-126
Speed change function ............................... 12-37
Speed change program ................................ 6-20
Speed change request (
Cd.15
) ............... 5-107
Speed control (Explanation of positioning terms)
..........................................................Appendix-89
Speed designation during OP shift (
Pr.56
)
....................................................................... 5-56
Speed differential compensation (
Pr.138
).. 5-76
Speed integral compensation (
Pr.117
)....... 5-64
Speed integral compensation (Explanation of
positioning terms).............................Appendix-89
Speed integral compensation changing ratio (
Pr.155
) .......................................................... 5-78
Speed limit function..................................... 12-23
Speed limit value (
Pr.8
) ............................ 5-26
Speed limit value (Explanation of positioning
terms) ................................................Appendix-89
Speed loop gain 1 (
Pr.114
)..........................5-64
Speed loop gain 2 (
Pr.116
)..........................5-64
Speed loop gain changing ratio (
Pr.154
) ....5-78
Speed loop gain (Explanation of positioning terms)
...........................................................Appendix-89
Speed loop mode (Explanation of positioning
terms) ................................................Appendix-89
Speed-position function selection (
Pr.200
) .5-32
Speed switching mode (
Pr.19
)..................5-32
Speed-position switching control (ABS mode)
........................................................................9-90
Speed-position switching control (INC mode)
........................................................................9-85
Speed–position switching control (Explanation of
positioning terms)..............................Appendix-89
Speed-position switching control movement
amount change register (
Cd.23
) ..............5-152
Speed-position switching control positioning
amount (
Md.29
).........................................5-124
Speed-position switching enable flag (
Cd.24
)
......................................................................5-148
Speed-position switching latch flag.............5-126
Speed-position switching signal ....................3-18
Speed-position switching control mode
(Explanation of positioning terms)....Appendix-89
Spiral interpolation .........................................9-60
SSCNET........................................................ A-14
SSCNET cable over all length.........................3-3
Standard speed switching mode...................9-12
Start Hour (
Md.5
) ......................................5-112
Start complete (Explanation of positioning terms)
...........................................................Appendix-89
Start complete signal .....................................3-13
Start data No. (
Da.12
) ..............................5-101
Start data pointer being executed (
Md.43
)
......................................................................5-132
Start details setting program..........................6-54
Start history..................................................5-112
Start history pointer (
Md.8
) .......................5-114
Start information (
Md.3
)............................5-112
Start Minute: second (
Md.6
).....................5-112
Start No. (
Md.4
).........................................5-112

Mitsubishi QD75M1 Specifications

General

Brand	Mitsubishi
Model	QD75M1
Category	Controller
Language	English