What causes excessive vibration in MTD 31BM62KE704 Snow Blower?
Excessive vibration in your MTD Snow Blower may be caused by: 1. Loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration persists, have the unit serviced by an authorized Service Center.
How to fix MTD 31BM62KE704 engine that fails to start?
If your MTD Snow Blower engine won't start, several factors could be at play. First, ensure the choke is in the CHOKE position and the spark plug wire is securely connected. Next, check that the fuel tank isn't empty or filled with stale fuel; if so, replenish it with clean, fresh fuel. Make sure you've primed the engine as per the Engine Manual. Inspect the spark plug for faults, cleaning, adjusting the gap, or replacing it if necessary. Verify the safety key is fully inserted into the switch. Lastly, if your model has an electric start, confirm the extension cord is properly connected to both the snow blower and a grounded 120V AC outlet.
What to do if MTD 31BM62KE704 engine fails to start?
If your MTD Snow Blower engine won't start, here's what you can check: 1. Ensure the choke control is in the ON position. 2. Make sure the spark plug wire is securely connected. 3. Verify the fuel tank isn't empty and contains fresh gasoline. 4. Prime the engine as detailed in the Operation section of your manual. 5. Inspect the spark plug; clean, adjust the gap, or replace it if necessary. 6. Confirm the safety key is fully inserted into the switch.
How to start my MTD 31BM62KE704 if the engine fails to start?
If the engine of your MTD Snow Blower fails to start, consider these possible causes: * The choke might not be in the CHOKE position. If so, move the choke to the CHOKE position. * The spark plug wire could be disconnected. Ensure the wire is connected to the spark plug. * The fuel tank may be empty or contain stale fuel. Refill the tank with clean, fresh gasoline. * The engine might not be primed. Prime the engine as instructed in the Operation Section. * The spark plug could be faulty. Clean, adjust the gap, or replace it. * The key may not be fully inserted into the ignition. Insert the key fully into the switch.
Why overhead chute crank does not stay stationary while throwing snow using an overhead chute control in MTD 31BM62KE704?
If the overhead chute crank on your MTD Snow Blower does not stay stationary, there might be insufficient preload applied to the chute control. Refer to the Service section to adjust the chute preload.
Why is my MTD 31BM62KE704 Snow Blower engine overheating?
If your MTD Snow Blower is overheating, it might be due to a low engine oil level. Ensure you fill the engine with the proper amount of engine oil.
What to do if MTD Snow Blower has excessive vibration?
If your MTD Snow Blower is vibrating excessively, it could be due to loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by an authorized Service Center.
What to do if MTD 31BM62KE704 fails to discharge snow?
If your MTD Snow Blower fails to discharge snow, several issues could be responsible. First, stop the engine immediately, disconnect the spark plug wire, and check for any clogs in the chute assembly. Clean the chute assembly and the inside of the auger housing using a clean-out tool. Also, stop the engine immediately, disconnect the spark plug wire and inspect the auger for any foreign objects and remove them with a clean-out tool. Finally, check the shear pins and replace them if sheared.
What to do if MTD 31BM62KE704 unit fails to discharge snow?
If your MTD Snow Blower fails to discharge snow, the chute assembly could be clogged, a foreign object might be lodged in the auger, the auger control cable may need adjustment, the auger belt might be loose or damaged or the shear pins may be sheared. To address this, stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool. Also remove any foreign objects from the auger. For cable and belt issues, refer to the corresponding sections, and replace any sheared pins.
Why is my MTD Snow Blower engine running erratically?
If your MTD Snow Blower engine is running erratically, with inconsistent RPM, consider the following potential causes: * The engine might be running on CHOKE. Move the choke lever to the RUN position. * The fuel could be stale. Fill the tank with clean, fresh gasoline. * There may be water or dirt in the fuel system. Drain the fuel tank and refill it with fresh fuel.
General| Auger Material | Steel |
|---|---|
| Stages | Single-stage |
| Chute Control | Manual |
| Engine Type | 4-cycle |
| Clearing Width | 21 inches |
| Starter Type | Recoil |
| Chute Rotation | 180 degrees |
To Next Page
