MTD OEM-190-032 User Manual

Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
IMPORTANT
OPERATOR’S MANUAL
42-inch Two-Stage Snow Thrower Attachment
For FastAttach™ Compatible Lawn Tractors & Garden Tractors
Model
OEM-190-032
190-032-101
6/2005
FORM NO. 769-01933

MTD OEM-190-032 Specifications

General

Clearing Width	24 in
Intake Height	21 in
Auger Material	Steel
Type	Two Stage
Engine Type	4-Cycle
Drive System	Disc Drive
Wheel Size	13 in x 4 in
Starter Type	Recoil

Summary

Rider Model Identification

Determine Your Rider Model

Locate the rider's model plate to identify the correct model series for installation.

Safe Operation Practices

Training

Read, understand, and follow all instructions and safety rules before operating the machine.

Preparation

Inspect the area, wear safety glasses, and use proper fueling procedures before operation.

Operation and Maintenance Safety

Operation Safety Guidelines

Follow operating instructions for efficient snow removal and safe machine use.

Maintenance and Storage

Check controls, safety devices, and store machine properly for longevity.

Carton Contents

Verify Included Parts

Check all parts against the list to ensure completeness before starting assembly.

Assembly - Models 600-649 & 800 Series

Mounting the Idler Pulley and Pin

Install the idler pulley and pin to the PTO engagement plate on manual PTO tractors.

Mounting the Belt Keeper

Secure the belt keeper to the tractor's frame near the engine pulley for proper belt routing.

Mounting the Undercarriage Assembly

Position and secure the undercarriage assembly beneath the tractor, connecting lift arms and PTO cable.

Assembly - Model Series 700-799

Bracket Assembly

Mount snow thrower assembly brackets to your tractor using provided hardware.

Undercarriage Assembly

Install the undercarriage assembly, including pulleys and belt, for 700-799 series models.

Assembling Controls

Attach Chute Directional Control

Connect the chute crank rods and control assembly for adjusting snow discharge direction.

Attach Lift Handle

Mount the lift handle and cable to raise and lower the snow thrower attachment.

Mounting Auger Housing

Mount Auger Housing Assembly

Position and secure the auger housing assembly to the tractor's front pivot support brackets.

Attach Support Tubes

Secure the right and left support tubes to the undercarriage assembly.

Belt Routing

Route Upper Drive Belt

Install the upper drive belt around pulleys for electric and manual PTO tractors.

Route Lower Drive Belt

Install the lower drive belt around the spindle, idler, and snow thrower drive pulleys.

Controls and Operation

Control Functions

Understand how to engage PTO, operate lift handle, and control chute direction.

General Operation Guidelines

Follow instructions for efficient snow removal, including speed, conditions, and path clearing.

Adjustments

Lift and Skid Shoe Adjustments

Adjust lift linkage and skid shoes for proper height and clearance.

Maintenance

Lubrication and Auger Shaft Care

Perform seasonal lubrication and auger shaft maintenance for optimal performance.

Parts List and Diagrams

Component Identification

Reference part numbers and descriptions for all snow thrower components.

Exploded View Diagrams

Visual representation of snow thrower parts and their assembly order.

Manufacturer's Limited Warranty

Warranty Coverage and Obtaining Service

Understand warranty terms, limitations, and the process for claiming service.