Need help?Do you have a question about the MTS Systems Temposonics R V Series and is the answer not in the manual?
General| Technology | Magnetostrictive |
|---|---|
| Housing Material | Stainless Steel |
| Protection Class | IP67 |
| Operating Temperature | -40°C to +85°C |
| Output Signal | Analog, SSI |
| Repeatability | ±0.001% F.S. |
| Supply Voltage | 10-30V DC |
Explains manual purpose, audience, and defines symbols/warnings for safe operation.
Specifies intended applications and lists potential misuses with their consequences.
Outlines safety precautions for installation, connection, and operation by qualified personnel.
Covers hazardous area safety, warranty terms, and sensor return process.
Details the structure and options for creating an order code for RP5 sensors.
Explains how to encode max speed or velocity values for RP5 order codes.
Details the structure and options for creating an order code for RH5 sensors.
Explains how to encode max speed or velocity values for RH5 order codes.
Describes the information found on the sensor's nameplate for identification.
Lists the certifications obtained by the sensor, including CE, EAC, and UL.
Details the items included in the scope of delivery for RP5 and RH5 sensor models.
Explains the principle of magnetostrictive position sensing and system construction.
Provides guidance on how to install the RP5 profile sensor using mounting clamps or T-slot nuts.
Details mechanical options for bushing on rod end and M4 thread for RH5 flanges.
Describes RH5 sensor models with specific threaded flanges and rod types.
Describes the RH5 sensor with a M22x1.5 threaded flange and 12.7mm rod.
Details the RH5 base unit, specifically for replacement purposes.
Guides rod-style sensor installation in fluid cylinders, focusing on mounting and sealing.
Explains the two methods for sealing the flange contact surface using O-rings.
Illustrates typical magnet types and their applications with sensors.
Provides instructions for mounting magnets, emphasizing concentricity and air gap.
Details considerations for mounting magnets with magnetic material, including spacer use.
Defines the minimum distance required between magnets for multi-position measurements.
Provides crucial notices regarding replacing the base unit, especially for predecessor models.
Gives detailed instructions for connecting sensors, focusing on EMC and grounding.
Highlights important points for using programming pins for analog output and safety.
Lists available position magnets for RP5 design with part numbers and specifications.
Lists available mounting accessories for RP5 design, including clamps and nuts.
Lists available position magnets for RH5 design with part numbers and specifications.
Lists available magnet spacers and O-rings for RH5 design with part numbers.
Lists available mounting accessories for RH5 design, including jam nuts and fixing clips.
Lists available M16 female connectors for analog output with specifications.
Lists available programming tools like TempoLink kit and hand programmer with part numbers.
Lists available PVC, PUR, and Teflon cables with specifications.
Describes single and dual channel analog output options and their capabilities.
Introduces methods for programming R-Series V Analog sensors using various tools.
Lists error conditions, their descriptions, and troubleshooting steps indicated by sensor LEDs.
Provides commissioning notices, including initial checks and magnet positioning.
Details the process of programming the sensor using the hand programmer for analog output.
Provides instructions for mounting the cabinet programmer on standard DIN rails.
Guides connecting the TempoLink smart assistant to the sensor and power supply.
Explains how to connect the TempoLink smart assistant to external devices via Wi-Fi.
Details how to connect the TempoLink smart assistant to a computer using a USB connection.
Describes how to establish a connection to the TempoLink smart assistant via a web browser.
Introduces the interface page for viewing and adjusting sensor settings.
Explains how to enter command mode to adjust sensor settings via the interface.
Describes how to adjust sensor settings after entering command mode using pencil icons.
Details how to adjust the configurable analog output range via the interface.
Explains how to adjust the output value for set point one (start of stroke).
Explains how to adjust the output value for set point two (end of stroke).
Details how to adjust the error output value for channel one.
Explains setting channel one function and adjusting magnet positions for set points.
Explains enabling the channel one over range setting to handle magnet travel beyond active stroke.
Describes changing set point units between millimeters and inches.
Explains how to save and exit command mode to transfer changed parameters to the sensor.
Details how to restore factory settings using the 'FACTORY RESET' function.
Lists error conditions, their descriptions, and troubleshooting steps indicated by sensor LEDs.
States that the sensor is maintenance-free.
Provides output specifications and measurement parameters for the RP5 sensor.
Provides output specifications and measurement parameters for the RH5 sensor.
A form for declaring that returned sensors are clean and safe for handling.
Provides port details for RH5-S and RH5-T sensors, including dimensions and notes.
Defines 'Analog output', 'Differential', 'Magnet Speed', 'Direction', and 'Measurement'.
Defines 'Resolution', 'Speed', 'Temperature', and 'Velocity'.
To Next Page
