Warranty
Machine Model _____________ Serial No. _______________ Date Of Purchase _________________
Warranty Period _____ months from date of purchase, non-transferrable.
Warranty Terms
Multicam Systems Pty Limited guarantees against defects in material and quality of manufacture for the period shown herein,
subject to proper application, use and maintenance of the equipment. Specifically Multicam Systems Pty Limited warrants the
Machine, on-board electronics, and drive systems for this period subject to proper use and maintenance of the machine.
A Line Conditioner must be fitted by a Licensed Electrician prior to or at the time of installation at the customers cost. The Line
Conditioner is designed to provide constant output voltage when there are fluctuations in the supply voltage. Regular servicing
of the System must be carried out at 3 monthly intervals or after 200 working hours whichever occurs first. Four weeks grace
may be granted outside of the 3 months by Multicam Systems. You will be contacted prior by the relative State Service
Manager. Failure to comply with these conditions of warranty will deem all Warranties Null and Void, without exception.
Attempts at servicing any or all of the System, by someone other than Multicam Service technician, will void all warranties
immediately.
All attachments and components, including but not limited to, spindles, vacuum pumps, dust collectors, material handling
systems and knife cutting attachments, supplied by third party manufacturers such as HSD S.r.l, Walter Perske GMBH, Trico,
UNIST, BFT, Rietschle, or any other supplier carry the warranty of their original manufacturer, with the exception of spindle
bearings. The use of non-recommended fluids in mist sprayer devices will void warranty on these devices. Any warranty
expressly stated or impliedly offered by Multicam Systems on these items is not in addition to the warranty offered by the
original manufacturer. Spindle motor bearings are warranted for a period of six months from the date shown herein, subject to
conditions of use and maintenance as outlined further in this manual. Use of non genuine tool holders or collets will void the
manufacturers warranty.
Warranty on vacuum pumps is subject proper use and maintenance as detailed in this manual. Inlet temperature is not to
exceed 50
o
C. Pumps are not to be enclosed and must have a minimum of 1m free space on all sides for ventilation.
Warranty Provisions
Multicam Systems Pty Limited will replace or repair, at our own discretion, any part found to be faulty in manufacture or
workmanship for the period as stated on this document. All items submitted for warranty repair must be shipped to the offices of
Multicam Systems Pty Ltd. All freight costs are to be borne by the customer and do not constitute part of the warranty
provisions.
The warranty provided by Multicam Systems Pty Limited does not extend to:-
i. any replacement or repair work carried out by any person other than an employee of Multicam Systems Pty
Limited; or
ii. any replacement or repair work required to be carried out as a result of damage or fault which arises as a
consequence of the customers’ inappropriate or incorrect operation of the Machine; or
iii. any replacement or repair work required to be carried out as a consequence of the failure on the part of the
customer to make available adequate or appropriate services and facilities advised by Multicam Systems Pty
Limited as being necessary for the proper operation of the Machine, including but not being limited to adequate or
appropriate power supply, or
iv. any replacement or repair work required to be carried out as a consequence of use of non-genuine components,
including but not being limited to tool holders and collets for spindles, or
v. any labour costs for any replacement, maintenance or repair work of an electrical nature which relates to any
electrical component on the Machine or the power supply to the Machine, machine accessories or to the building in
which the Machine is located. Engagement of qualified electrical trades persons shall be at the expense of the
customer and in accordance with state legislation.
vi. Multicam Systems Pty Ltd is not liable for any claim, production loss, damage or expense, without limitations
whether direct or indirectly arising out of machine down time caused by warranty claims.
Warranty is non-transferrable. Multicam Systems Pty Limited advises that any replacement or repair work of an electrical nature
should always be carried out by persons holding appropriate qualifications to carry out such work including any qualifications
required under any State or Federal law.
Signed on behalf of Multicam Systems Pty Ltd;
_______________________ _________________________________ ________________
AUTHORISED SIGNATURE NAME DATE
Signed on behalf of (company name): _____________________________________________
________________________________ _________________________________ ________________
AUTHORISED SIGNATURE NAME DATE
To Next Page
Loading...