MUTOH Kona 1400 - Service Manual

146 pages

Save Page as PDF

To Next Page

Service

Manual

For service technicians only!

Based on firmware version 3.0.0

A1, A2, A3 and A4

For machine versions:

& Mutoh CutServer version 3.0.0

Main Page

Default Chapter5
- Table of Contents5
Chapter 1 Regulations and Safety Information9
Warnings, Cautions and Notes10
Compliance with the Following Regulations10
Important Notes11
Safety Labels12
Chapter 2 Product Overview13
Dimensions Machine14
Installation Environment Requirements14
- Power Supply14
- Ambient Conditions14
- Room Conditions15
Part Names and Functions16
Overview Operation Panel17
- Main Menu17
- Settings or Actions Menu18
- Settings or Actions Menu19
- Adjust Value Menu19
Menu Overview20
- User Mode20
- Diagnostics Mode 1 and 221
- Diagnostics Mode 1 and 223
Machine Version24
Chapter 3 Part Replacement25
Cover Removal27
- Side Covers28
- Y-Rail Cover29
- Penhead Cover30
- Front Platen31
- Rear Platen32
X-Motor and Drive Belt33
Y-Motor Assembly35
- Exploded View35
- Y-Motor36
- Y-Drive Pulley and Speed Reduction Belt38
- Y-Return Pulley39
Penhead Assembly40
- Exploded View40
- Penhead FFC (Flexible Flat Cable)41
- Penhead Assembly44
- Penhead Drive Belt47
- Sheet-Off Mechanism49
- EPOS Sensor Block50
- Y-Origin Flex PCB52
Grit Shaft53
- Exploded View53
- Grit Shaft and Support Rollers54
Pressure Roller Assembly59
- Exploded View59
- Pressure Roller60
- Pressure Roller Assembly61
Cutting Mat66
Electronics67
- Mainboard67
- And y Motor Fuse74
- Penhead PCB75
- Power Supply78
- Touchscreen80
- Sensors81
- Vacuum Fans83
Chapter 4 Adjustments and Calibrations85
Mechanical Adjustments86
- Drive Belt Tension86
- Y Drive Belt Tension87
- Penhead Drive Belt Tension88
- Pressure Roller Pressure90
- Sheeting-Off Knife Position91
- YZ Measurement93
Software and Drivers94
- Download Latest Software and Drivers94
- Firmware Installation94
- How to Uninstall the USB Drivers96
- How to Install the USB Drivers97
- USB Icon97
Parameters98
- Backup Parameters of Machine98
- Restore Parameters of Machine99
Mutoh Cutserver Tests100
- Tracking Test100
- XY-Distance Accuracy Test102
EPOS Calibration103
- Diagnostics Mode105
Chapter 5 Diagnostics Mode105
Introduction106
How to Start up in Diagnostics Mode 1 and 2106
- Diagnostics 1106
- Diagnostics 2107
Menu Overview108
- Connection109
- Encoder110
- PWM Test111
- Defaults112
- Accuracy113
- YZ Profile114
- Tool Force115
- Actuators115
- Sensors116
- Aging117
- Screen119
Chapter 6 Troubleshooting121
Troubleshooting When no Error Is Displayed122
- General Troubleshooting122
- Recoverable Error Messages with no Error ID Number126
Troubleshooting When an Error Is Displayed128
- Errors with Error Number (ID 1009-6115)128
- Contourcutting Errors and Warnings (ID 6201-6271)131
- MGL Errors (ID 4000-5000)138
- Brevid_Error_Hw_Revision (6110-6120)139
- Fpga Errors (6140 - 6150)140
- Ram Errors141
- Other Errors142
- Pressure Roller Assembly Replacement144

MUTOH Kona 1400 - Service Manual

Table of Contents

Other manuals for MUTOH Kona 1400

Related product manuals