Why is there no sound coming from my NAD C 275BEE Amplifier?
If there is no sound coming from your NAD Amplifier, verify that the AC lead is plugged in and the power is switched on, ensuring the correct ATO logic configuration. Also, check that an active input signal is being applied through the input sockets and that the input level control is properly adjusted.
What to do if my NAD Amplifier has no power?
If your NAD Amplifier has no power, ensure the power cord is securely plugged into the wall outlet. Also, check that the power switch is set to the 'ON' position.
What to do if POWER/STANDBY LED stays red on NAD C 275BEE Amplifier?
If the POWER/STANDBY LED on your NAD Amplifier stays red when you turn the power on, switch the amplifier off and inspect the speaker cable connections at both speaker terminals on the rear panel for any short circuits.
Why is there no sound from one channel of my NAD C 275BEE Amplifier?
If you're experiencing no sound from one channel of your NAD Amplifier, check the speaker connections and the condition of the speakers themselves. Additionally, inspect the input leads and their connections to ensure they are properly connected and undamaged.
How to fix weak bass or diffused stereo image on NAD Amplifier?
To correct weak bass or a diffused stereo image on your NAD Amplifier, check the connections to all speakers in the system to ensure they are wired correctly and in phase.
What to do if NAD C 275BEE Amplifier is always at standby mode?
If your NAD C 275BEE Amplifier remains in standby mode and cannot be switched on using the front panel button, ensure that the +12V TRIGGER IN/INPUT SENSE switch is set to the 'OFF' position.
Covers reading instructions, cleaning, handling, water, ventilation, and power source safety.
Details power sources, grounding, cord protection, and service requirements.
Addresses outdoor antennas, lightning, power lines, heat, and mounting.
Covers overloading, object entry, liquid spills, general cautions, and environmental protection.
Provides an overview of initial setup and operation procedures for the amplifier.
Step-by-step instructions for the initial setup and connection of the amplifier.
Guidelines for proper placement, ventilation, and connecting speaker wires.
Detailed instructions and warnings for connecting bare wires and pin connectors to terminals.
Description of the front panel buttons and indicators like Standby, Bridge Mode, and Clipping.
Details the various inputs, outputs, switches, and connectors on the rear panel.
Explains the different ways the amplifier can be turned on and managed automatically.
Provides solutions for common problems like no power, no sound, or weak bass.
Lists detailed technical specifications for output power, impedance, frequency response, and dimensions.
Covers reading instructions, cleaning, handling, water, ventilation, and power source safety.
Details power sources, grounding, cord protection, and service requirements.
Addresses outdoor antennas, lightning, power lines, heat, and mounting.
Covers overloading, object entry, liquid spills, general cautions, and environmental protection.
Provides an overview of initial setup and operation procedures for the amplifier.
Step-by-step instructions for the initial setup and connection of the amplifier.
Guidelines for proper placement, ventilation, and connecting speaker wires.
Detailed instructions and warnings for connecting bare wires and pin connectors to terminals.
Description of the front panel buttons and indicators like Standby, Bridge Mode, and Clipping.
Details the various inputs, outputs, switches, and connectors on the rear panel.
Explains the different ways the amplifier can be turned on and managed automatically.
Provides solutions for common problems like no power, no sound, or weak bass.
Lists detailed technical specifications for output power, impedance, frequency response, and dimensions.
General| Power Output (Stereo) | 150W (8 Ohms) |
|---|---|
| Total Harmonic Distortion | <0.003% |
| Damping Factor | >100 (8 Ohms) |
| Input Sensitivity | 1.15V |
| Signal-to-Noise Ratio | > 100 dB |
| Input Impedance | 20 kOhms |
| Dimensions (W x H x D) | 435 x 132 x 350mm |
| Weight | 15 kg |
| Frequency Response | 20Hz-20kHz |
To Next Page
