NAD D 3045 - TV Connect Feature; TV Connect Overview and Setup

ENGLISH
AUTO STANDBY
The D 3045 can be setup to automatically go to standby mode if there is
no user interface interaction and no active Source input within 30 minutes.
Auto standby mode can be enabled or disabled by the following steps.
ENABLE AUTO STANDBY MODE
• While at standby mode, press and hold “OFF” button of the AMP 3
remote control until the o (Standby) indicator blinks once.
• At operating mode and with auto standby enabled, the D 3045
will automatically go to standby mode if there is no user interface
interaction and no active Source input within 30 minutes.
DISABLE AUTO STANDBY MODE
• While at standby mode, press and hold “OFF” button of the AMP 3
remote control until the o (Standby) indicator blinks twice.
• At operating mode and with auto standby disabled, D 3045 will not go
to standby mode at any time unless directly initiated by pressing top
panel’s o (Standby) switch or OFF button of AMP 3 remote control.
AUTO SENSE
Auto sense feature enables the D 3045 to wake up from standby mode and
starts operation by selecting OPTICAL 1, OPTICAL 2 or the last digital source
before going to standby mode.
CONDITIONS FOR AUTO SENSE
• For Auto Sense to work, Auto Standby must be set to ON with D 3045
going rst to standby mode.
• If IR Learning with TV remote control is successfully completed and
with D 3045 going to standby mode, auto sense is activated upon
detection of active digital input only from OPTICAL 1 or OPTICAL 2
inputs.
- With this condition, D 3045 wakes up and automatically switches to
OPTICAL 1 or OPTICAL 2.
• If no IR Learning is conducted, auto sense is activated upon detection
of active input from the last source (limited only to the digital sources)
before the D 3045 goes to standby mode.
- With this condition, D 3045 wakes up and automatically switches to
the last selected digital source prior to the D 3045 going to standby
mode.
ENABLE AUTO SENSE MODE
• While in standby mode, press and hold “SOURCE d” button of the
AMP3 remote control until the o icon on the top screen wakes up and
blinks once.
DISABLE AUTO SENSE MODE
• While at standby mode, press and hold “SOURCE d” button of the
AMP3 remote control until the o icon on the top screen wakes up and
blinks twice.
TV CONNECT
TV Connect is a new software enabled feature that allows the D 3045
to provide the sound for your TV. TV Connect enables D 3045 to learn
the mute and volume control commands from any TV remote control.
Additionally, the D 3045 will automatically power up to OPTICAL source
upon detection of digital TV output signal at OPTICAL 1 or OPTICAL 2
input.*
With TV Connect fully integrated, you can use your TV remote control to
manage the following features of D 3045:
1 Adjust Volume up/down
2 Enable or disable MUTE function
3 Switch ON D 3045
HOW TO CONFIGURE YOUR D 3045 WITH TV CONNECT
TV Connect setup requires the digital optical output of your TV to be
connected to the OPTICAL 1 or OPTICAL 2 input of your D 3045. With
this setup and with proper conguration, when you turn ON your TV, the
D 3045 powers up from standby mode and the TV input (OPTICAL 1 or
OPTICAL 2) is automatically selected.* The D 3045 can also be awakened
by pressing the top panel’s o and the power ON button of either AMP 3
remote control or TV’s remote control.
The following congurations are necessary to integrate TV Connect with
your D 3045.
• Enable auto standby mode.
• Enable auto sense mode.
• Perform IR (infrared) learning with TV remote control.
ENABLE AUTO STANDBY MODE
While at standby mode, press and hold “OFF” button of the AMP 3 remote
control for a few seconds until all indicators on the front screen wake up
and blink once.
ENABLE AUTO SENSE MODE
While in standby mode, press and hold “SOURCE d” button of the AMP3
remote control until the o icon on the top screen wakes up and blinks once.
OTHER FEATURES
11