40 41
BLENDER
TROUBLESHOOTING
Please check the following troubleshooting items before contacting
customer service. If you have any questions or issues using this
product, please contact our customer support team at
namawell.com/contact or (833) 253-6262.
For faster service, please have the following information available: Order number, Model number,
Serial number (located on the bottom of the base).
HOW TO DISASSEMBLE AND CLEAN
01. ADD 16 OZ. OF WARM WATER WITH 23
DROPS OF LIQUID DISH SOAP INTO
THE JUG.
02. PLACE THE JUG ON THE BASE AND
ASSEMBLE THE LID AND DOSING CAP
ONTO JUG.
03. TURN THE CONTROL KNOB TO SELECT
AUTO CLEAN AND THEN PRESS THE START
BUTTON TO CLEAN.
04. WHEN AUTO CLEAN CYCLE IS COMPLETE,
ALLOW BLADES TO STOP ROTATING
COMPLETELY, THEN ROTATE CONTROL
KNOB TO STOP POSITION. DISASSEMBLE
JUG, LID AND DOSING CAP AND RINSE
THOROUGHLY TO REMOVE SOAP RESIDUE.
CAUTION DO NOT REMOVE THE JUG
FROM BASE UNTIL THE BLADES STOP
ROTATING COMPLETELY.
05. FOR DEEPER CLEANING OF PARTS, OR TO
CLEAN ANY REMAINING RESIDUE, USE A
NONABRASIVE SPONGE OR BRUSH WITH
SOAP AND WATER.
CAUTION SHARP BLADES BE CAREFUL
AND AVOID CONTACT WITH SHARP
BLADES AS IT MAY CAUSE INJURY.
06. CLEANING THE BASE UNPLUG THE BASE
FROM POWER SOURCE AND PULL OUT THE
POWER CORD TO TURN OFF POWER. WIPE
BASE WITH A SOFT TOWEL OR SPONGE,
WHICH MAY BE A LITTLE DAMP TO HELP
REMOVE ANY RESIDUE.
NOTE: DO NOT USE A DISHWASHER FOR
CLEANING ANY OF THE PARTS, AS IT MAY
CAUSE DAMAGE TO THE PARTS.
NOTE: DO NOT SOAK THE JUG IN LIQUID,
AS IT MAY CREATE RUST OR DAMAGE THE
PRODUCT.
NOTE: BLADES ARE NOT DESIGNED TO BE
DETACHED FROM JUG. DO NOT ATTEMPT
TO DETACH BLADES FROM JUG AS IT WILL
DAMAGE THE PRODUCT AND WILL NO
LONGER BE SAFE TO USE.
JUICER AND BLENDER
JUICER
THE PRODUCT DOES NOT OPERATE WITH THE BASE ONLY.
To operate the product either the chamber set of the juicer or the jug of the blender must be assembled
correctly on the base. Make sure the power is o when assembling or disassembling the product.
ASSEMBLE IT SO THAT IT IS ALIGNED WITH THE SAFETY SENSOR.
Check if it is assembled in accordance with the Guide mark. Make sure to turn the power o when
assembling or disassembling the product.
THERE ARE CRACKS OR SCRATCH MARKS ON THE PRODUCT.
These are normal marks on the parts and do not aect the operation at all. During the molding process
of creating the parts, it is normal to have curved or straight lined mold marks.
PRODUCT WILL NOT TURN ON.
Check to ensure the product is properly assembled, it will not work if assembled incorrectly. Refer to
pages 12-15 for proper juicer assembly and pages 32-33 for proper blender assembly. The motor base
has a safety sensor to protect it from overheating after long periods of use. Please allow the motor
base to cool down for about 30-60 minutes and it will operate normally.
THE JUICER STOPS OPERATING DURING JUICING.
The juicer may have jammed due to excessive ingredients or extremely thick ingredients being inserted,
and may need to activate reverse. Refer to pages 16-17 of this manual for using the control knob and
reverse function. For safety, continuous operation of the juicer from start will automatically stop when
display timer hits 30 minutes. Press the Start/Stop button again to re-start operation.
JUICE LEAKS THROUGH PULP OUTLET IMMEDIATELY AFTER THE INGREDIENTS ARE INSERTED.
Depending on the inserted ingredients, small amounts of juice may leak through the pulp outlet.
This is not a product defect but rather a phenomenon caused by the characteristics of the ingredients.
The leakage will stop once the product starts running. If the leakage continues, contact Nama
customer service.
JUICE FLOWS BACK INTO THE HOPPER.
When juicing with the juice cap closed, the juice may ow backward into the hopper. If the contents
are not suciently discharged even after opening the juice cap again, open the hopper cover and
empty out the contents.
16 oz.
Auto Clean 19sec.
To Next Page
Loading...