EasyManua.ls Logo

Napoleon GD36PTR User Manual

Napoleon GD36PTR
62 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
W415-0773 / E / 03.13.12
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleon replaces.com • ask@napoleonproducts.com
1.28C
$10.00
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
SAFETY INFORMATION
!
WARNING
- Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbours phone. Follow the gas suppliers
instructions.
If you cannot reach your gas supplier, call the
re department.
- Installation and service must be performed by a
quali ed installer, service agency or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certi ed kit is used.
If the information in these instructions
are not followed exactly, a re or
explosion may result causing property
damage, personal injury or loss of life.
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.
GD36NTR
BGD36NTR
NATURAL GAS MODEL
GD36PTR
BGD36PTR
PROPANE GAS MODEL
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33 ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS
BGD ILLUSTRATED

Table of Contents

Other manuals for Napoleon GD36PTR

Questions and Answers:

Napoleon GD36PTR Specifications

General IconGeneral
BrandNapoleon
ModelGD36PTR
CategoryIndoor Fireplace
LanguageEnglish

Summary

SAFETY INFORMATION

1.0 INSTALLATION OVERVIEW

2.0 INTRODUCTION

2.1 GD36 DIMENSIONS

Detailed physical dimensions for the GD36 model.

2.2 BGD36 DIMENSIONS

Detailed physical dimensions for the BGD36 model.

2.3 GENERAL INSTRUCTIONS

Key operational and safety guidelines for the appliance.

2.4 GENERAL INFORMATION

Appliance rates, efficiencies, and general operational data.

2.5 RATING PLATE INFORMATION

Appliance certification, model specifics, and safety standards.

3.0 VENTING

3.1 VENTING LENGTHS AND COMPONENTS

Specifies approved vent components and allowable lengths for optimal performance.

3.2 TYPICAL VENT INSTALLATION

Illustrates standard methods for installing top and rear vent configurations.

3.4 MINIMUM AIR TERMINAL LOCATION CLEARANCES

Defines required clearances around the vent terminal based on location.

3.8 TOP EXIT HORIZONTAL TERMINATION

Procedures and calculations for top-exit horizontal venting configurations.

3.9 REAR EXIT HORIZONTAL TERMINATION

Procedures and calculations for rear-exit horizontal venting configurations.

4.0 PRE-INSTALLATION PREPARATION

4.1 GD36 REAR EXIT

Specific preparation steps for GD36 model rear exit configuration.

4.2 GD36 TOP EXIT

Specific preparation steps for GD36 model top exit configuration.

5.0 INSTALLATION

5.1 WALL AND CEILING PROTECTION

Guidelines for protecting surrounding combustible materials during installation.

5.3 USING RIGID VENT COMPONENTS

Instructions for installing rigid vent pipes and terminals.

5.4 VERTICAL THROUGH EXISTING CHIMNEY

Procedures for venting the appliance through a masonry chimney.

5.6 GAS INSTALLATION

Critical steps for connecting and securing the gas supply line.

6.0 FRAMING

6.1 GD36 FRAMING

Specific framing dimensions and considerations for the GD36 model.

6.3 MINIMUM ENCLOSURE CLEARANCES

Specifies required clearances to combustibles for the appliance enclosure.

7.0 FINISHING

7.1 DOOR REMOVAL AND INSTALLATION

Step-by-step guide for removing and reinstalling the appliance door.

7.3 LOG PLACEMENT

Precise placement instructions for logs for correct function and appearance.

8.0 OPTIONAL BLOWER INSTALLATION

9.0 OPERATION

10.0 ADJUSTMENT

10.1 PILOT BURNER ADJUSTMENT

How to adjust the pilot flame size for proper appliance operation.

10.2 VENTURI ADJUSTMENT

Guide for adjusting the air shutter for correct flame characteristics.

11.0 MAINTENANCE

11.1 DOOR GLASS REPLACEMENT

Step-by-step instructions for safely replacing the appliance door glass.

12.0 REPLACEMENTS

13.0 TROUBLESHOOTING

14.0 WARRANTY

15.0 SERVICE HISTORY

Related product manuals