NCR SelfServ 84 Walk-Up - Variant Details: CEN I, Standard Collar ATM (Security); Security Bolt and Hole Specifications

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved
B006‐7519‐G000
VariantDetails‐CENI,Standard CollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐3
SECURITYBOLTS
Boltsandanchorsmustbesuppliedbytheowningorganisation.
TomeetsecuritystandardstheATMmustbeboltedtothefloor,throughallof
theboltholes,usingboltswithanchorwashersasspecifiedbelow.Boltsand
anchorwashersaretobesuppliedbytheowningorganisation.
Makesurethatthefloororplinthiscapableofwithstandingthel
oading
imposedbytheanchorpointsforthesebolts.
Ifanadjustableplinthisused,itmustbeboltedtothefloortothesame
specificationastheATM.
TheminimumspecificationforboltsandwasherstosecuretheATMtoa
concreteflooris:
 Bolts
 Type‐eitherresinanchororshieldanchorbolts
 Size‐M16(5/8in.)
 MinimumLength‐150mm(5.9in.)
 Strength‐hightensile(minimumISOpropertyclass8,8).
 Washers
 Type‐flat,steel(asperDIN7349orequivalent)
 Size‐M16(5/8in.)
 Outerdiameter‐nogreaterthan40mm(1.58in.)
 Minimumthickness‐6mm(0.2in.).
BOLTHOLES
TheATMshouldbeboltedtothefloororplinth,throughalltheholesmarked
‘A’,usingfourboltswithanchorwashers.
Theholemarked‘B’enablesanalarmtobefitted.
ShortSleeve
LongSleeve
B
A
A
A
A
Hole in Wall
203 mm (7.99 in.)
Maximum
390 mm
(15.35 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
284.5 mm
(11.20 in.)
770 mm
(30.31 in.)
169.5 mm
(6.67 in.)
800 mm
(31.50 in.)
164 mm
(6.46 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
136 mm
(5.35 in.)
18 mm
(0.70 in.)
100.5 mm
(3.96 in.)
Hole A Bolt Holes Hole B (Alarm Hole)
40 mm
(1.57 in.)
40 mm
(1.57 in.)
21 mm
(0.83 in.)
25 mm
(0.98 in.)
28 mm
(1.10 in.)
65 mm
(2.56 in.)
45 mm
(1.77 in.)
28 mm
(1.10 in.)
B
A
A
A
A
Hole A Bolt Holes Hole B (Alarm Hole)
330 mm
(12.99 in.)
Maximum
504 mm
(19.84 in.)
Hole in Wall
500 mm
(19.68 in.)
250 mm
(9.84 in.)
284.5 mm
(11.20 in.)
770 mm
(30.31 in.)
169.5 mm
(6.67 in.)
800 mm
(31.50 in.)
164 mm
(6.46 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
136 mm
(5.35 in.)
18 mm
(0.70 in.)
100.5 mm
(3.96 in.)
40 mm
(1.57 in.)
40 mm
(1.57 in.)
21 mm
(0.83 in.)
25 mm
(0.98 in.)
28 mm
(1.10 in.)
65 mm
(2.56 in.)
45 mm
(1.77 in.)
28 mm
(1.10 in.)