NEC NP-V260 User Manual

iv
Important Information
- If the projector does not operate normally when you follow the instructions described in this user's manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
• Disconnect the power cord and any other cables before carrying the projector.
• Turn off the projector and unplug the power cord before cleaning the cabinet or replacing the lamp.
• Turn off the projector and unplug the power cord if the projector is not to be used for an extended period of time.
• When using a LAN cable (V300X/V260X/V300W/V260W only):
For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.
CAUTION
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry or
hang (from the wall or ceiling) the projector can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside the
soft case could be damaged.
• Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[SETUP] → [OPTIONS(1)] → [FAN MODE] → [HIGH].)
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blink-
ing green.
Doing so could cause premature lamp failure.
• Parts of the projector may become temporarily heated if the projector is turned off with the POWER button or if
the AC power supply is disconnected during normal projector operation.
Use caution when picking up the projector.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not heat, take apart, or throw batteries into fire.
• If you will not be using the remote control for a long time, remove the batteries.
• Ensure that you have the batteries' polarity (+/–) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used batteries according to your local regulations.
Lamp Replacement
• Use the specified lamp for safety and performance.
• To replace the lamp, follow all instructions provided on page 81.
• Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE.
PLEASE REPLACE THE LAMP. USE THE SPECIFIED LAMP FOR SAFETY AND PERFORMANCE] appears. If
you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and
pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.

NEC NP-V260 Specifications

General

Native aspect ratio	4:3
Projection distance	1.2 - 13 m
Vertical scan range	50 - 120 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	DLP
Contrast ratio (typical)	2000:1
Screen size compatibility	33 - 300 \
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	-40 - 40 °
Focus	Manual
Throw ratio	1.95 - 2.15:1
Zoom capability	Yes
Focal length range	21.83 - 24 mm
RS-232 ports	1
Maximum analog resolution	1920 x 1080 pixels
Lamp type	AC HID
Lamp power	180 W
Light source type	Lamp
Service life of light source	3500 h
Service life of light source (economic mode)	5000 h
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Component video (YPbPr/YCbCr) in	0
Supported video modes	1080i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC 4.43, PAL, PAL L, PAL M, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1360 x 768 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 800 x 600 (SVGA)
RMS rated power	7 W
Placement	Ceiling
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	233 W
Power consumption (standby)	4 W
Power consumption (PowerSave)	0.5 W
Power consumption (economy mode)	210 W
Noise level	34 dB
Certification	CE; ErP; ÜV GS
Noise level (economic mode)	31 dB
Storage temperature (T-T)	-20 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Cables included	AC, VGA
Remote control type	IR
Sustainability certificates	RoHS

Weight and Dimensions

Depth	247 mm
Width	310 mm
Height	95 mm
Weight	2500 g