NEC NP-V260 User Manual

81
6. Maintenance
 Replacing the Lamp
When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red. Even though the lamp may
still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to
clear the lamp hour meter. (→ page 79)
CAUTION
• Use the specified lamp for safety and performance.
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
and then disconnect the power cord. Allow at least one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except one lamp cover screw and three lamp housing screws. You could receive
an electric shock.
• Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might cause
an unwanted shadow and poor picture quality.
• The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours
after the lamp has reached the end of its life. If this happens, be sure to replace the lamp. If you continue to use
the lamp after the lamp reaches the end of its life, the lamp bulb may shatter, and pieces of glass may be scattered
in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
*NOTE: This message will be displayed under the following conditions:
• for one minute after the projector has been powered on
• when the (POWER) button on the projector cabinet or the POWER OFF button on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
To replace the lamp:
Optional lamp and tools needed for replacement:
• Replacement lamp: NP13LP (V260X/V230X/V260/V230/V260W)
NP18LP (V300X/V300W)
• Phillips screwdriver or equivalent

NEC NP-V260 Specifications

General

Native aspect ratio	4:3
Projection distance	1.2 - 13 m
Vertical scan range	50 - 120 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	DLP
Contrast ratio (typical)	2000:1
Screen size compatibility	33 - 300 \
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	-40 - 40 °
Focus	Manual
Throw ratio	1.95 - 2.15:1
Zoom capability	Yes
Focal length range	21.83 - 24 mm
RS-232 ports	1
Maximum analog resolution	1920 x 1080 pixels
Lamp type	AC HID
Lamp power	180 W
Light source type	Lamp
Service life of light source	3500 h
Service life of light source (economic mode)	5000 h
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Component video (YPbPr/YCbCr) in	0
Supported video modes	1080i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC 4.43, PAL, PAL L, PAL M, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1360 x 768 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 800 x 600 (SVGA)
RMS rated power	7 W
Placement	Ceiling
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	233 W
Power consumption (standby)	4 W
Power consumption (PowerSave)	0.5 W
Power consumption (economy mode)	210 W
Noise level	34 dB
Certification	CE; ErP; ÜV GS
Noise level (economic mode)	31 dB
Storage temperature (T-T)	-20 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Cables included	AC, VGA
Remote control type	IR
Sustainability certificates	RoHS

Weight and Dimensions

Depth	247 mm
Width	310 mm
Height	95 mm
Weight	2500 g