NEC PE506UL User Manual (English)

Other manuals for NEC PE506UL

User Manual123 pages

Quick Setup Guide2 pages

Questions and Answers:

C
Charlotte ReyesAug 15, 2025
How to fix NEC PE506UL that does not turn on?
- F
  fred58Aug 15, 2025
  If your NEC Projector isn't turning on, start by checking that the power cord is securely plugged in and the power button on the projector or remote is switched on. Overheating can also prevent the projector from turning on; ensure there's sufficient ventilation and move it to a cooler spot if necessary. The light module might need a minute to light up after being turned off. If using the projector above 5500 feet/1700 meters, make sure the [High altitude] setting is enabled. If you have just turned the projector off, wait for a moment. As a last resort, unplug the power cord, wait 5 minutes, and then plug it back in.
P
Paul HortonAug 18, 2025
How to fix NEC Projector that does not turn on or shut down?
- K
  Katie ShepherdAug 18, 2025
  If your NEC Projector won't turn on or shut down, here are a few things to check: First, ensure the power cord is securely plugged in and that the power button on both the projector and the remote are switched on. Check if the projector has overheated. If so, wait a full minute before attempting to power it on again. If you're using the projector at an altitude above 1700 meters / 5577 feet, verify that the altitude setting is correctly configured. You may need to set [High altitude] to "On". If none of that works, unplug the power cord, wait 5 minutes, and then plug it back in.
P
Philip PerryAug 21, 2025
What to do if the picture suddenly becomes dark on my NEC PE506UL?
- D
  Deanna BeckAug 21, 2025
  If the picture on your NEC Projector suddenly becomes dark, it might be in Forced ECO mode due to high ambient temperature. You should also check your contrast and brightness settings, and verify that you're using the correct image mode settings.
G
gnormanAug 25, 2025
How to fix a fuzzy picture on my NEC PE506UL Projector?
- I
  icomptonAug 25, 2025
  To fix a fuzzy picture on your NEC Projector, first adjust the focus. Ensure that the projector is positioned at the proper projection distance. If the lens is dirty, it requires cleaning. Also, if you've recently moved the projector from a cold to a hot environment, condensation may have formed on the lens; wait until it evaporates before turning the projector on.
J
James EllisAug 27, 2025
How do I correct a non-square image on my NEC PE506UL?
- M
  melissa60Aug 28, 2025
  To correct a non-square image on your NEC Projector, begin by repositioning the projector to improve its angle relative to the screen. Additionally, use the Keystone correction function to rectify any trapezoidal distortion.
J
Jackson CabreraAug 30, 2025
What to do if there is no picture on my NEC PE506UL Projector?
- J
  jimmymillerAug 30, 2025
  If your NEC Projector isn't displaying an image, try these steps: First, make sure the correct input source is selected. If that doesn't work, press the SOURCE button or one of the source buttons again. Check that all cables are properly connected. Adjust the brightness and contrast in the menus. Ensure the AV-MUTE button hasn't been activated. If you've enabled the Security function, enter your registered keyword. Also, try reinstalling or updating the driver for your computer's graphics card. When connecting to a notebook PC, ensure the projector is in standby mode before powering on the PC. Finally, if the screen goes blank when using the remote, it might be due to your computer's screen-saver or power management settings.
P
parkerjessicaSep 3, 2025
What to do if my NEC PE506UL will turn off?
- C
  carrollericaSep 3, 2025
  To prevent your NEC Projector from turning off unexpectedly, make sure that the [Power management] setting is set to “Off.”
E
Edward MillerSep 5, 2025
Why is there no picture on my NEC PE506UL Projector?
- J
  Jeffrey GarciaSep 6, 2025
  If there's no picture on your NEC Projector, several factors could be at play. First, ensure the correct input is selected and all cables are properly connected. Try adjusting the brightness and contrast settings in the menu. Also, verify that the AV-MUTE button hasn't been activated. If these steps don't resolve the issue, try resetting the projector to its factory default settings via the Expand Menu. If the security function is enabled, make sure you enter the registered keyword. Reinstalling or updating your graphics card driver may also help. Connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. Finally, if using the remote control, the computer’s screen-saver or power management software may be the cause.
M
mary12Sep 8, 2025
Why does the picture suddenly become dark on my NEC PE506UL?
- M
  Mrs. Teresa DuncanSep 8, 2025
  If the picture on your NEC Projector suddenly becomes dark, start by checking your contrast and brightness settings. Next, verify that you're using the correct image mode settings. Keep in mind that the brightness will automatically reduce to protect the unit when the setting condition is over approximately 2600 meters / 8530 feet.
E
Elizabeth SmithSep 12, 2025
How to fix a fuzzy picture on NEC PE506UL?
- D
  Destiny RamosSep 12, 2025
  If your NEC Projector's picture looks fuzzy, first try adjusting the focus. If that doesn't sharpen the image, reposition the projector to improve its angle to the screen. Make sure the distance between the projector and the screen falls within the lens's adjustment range. Also, consider whether the lens has been shifted beyond its guaranteed range. Lastly, if there's condensation on the lens, let the projector stand until it clears.

NEC PE506UL Specifications

General

Resolution	1920 x 1200 (WUXGA)
Light Source	Laser
Speaker	10W
Display Technology	DLP
Light Source Life	20, 000 hours
Lens Shift	Horizontal: ±20%
Keystone Correction	Vertical: ±30 degrees
Input Connectors	HDMI, VGA
Output Connectors	Audio 3.5mm x 1
Control	RS-232, LAN, USB
Brightness	5000 ANSI Lumens