NetApp FAS2020 User Manual

FAS2020 System
Installation and Setup
Copyright © 2010 NetApp, Inc. All rights reserved.
Unpack and verify contents
Before you begin
1 2
If you have not already done so, gather the required information and confirm your site
requirements, as described in the Site Requirements Guide at http://now.netapp.com/.
Your system comes with an accessory kit that includes the following components:
- This installation poster - Power cables
- Software license flyer - DB-9 to RJ-45 console adapters
- Grounding kit - Rail kit (for two-post and four-post racks)
Install in rack
3
Caution: Use only the NetApp
®
rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system.
Four-post rack
Cable the system
4
Cable controllers
Network cable to Remote Management port
4
RJ-45 to DB-9 adapter to console port (required)
1
Fibre
Channel
Ethernet
Console
Remote
Management
Port
Port labels
Network cables to e0a and e0b ports
3
Console cable to adapter
2
Boot the system and proceed with setup
5
- Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate.
- Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/.
Cable disk shelves
These are a few common configurations. For additional options, see Supported Configurations for
FAS2000-series Systems at http://now.netapp.com.
or or
Note: See the rail kit installation flyer included with the rail kit for the two-post procedure.
210-03961+D0
Mounting
bracket
(2x)
6
e0be0a
8
0a 0b
Note: The disk shelf IDs for the
disk shelves should be set in the
range 1 to 6.
1
0
Shelf ID
switch
Setting the disk shelf IDs
e0be0a0a 0b
8
Active/Active NAS or ISCSI:
1 Fibre Channel Disk Shelf Stack (Multipath)
1
Controller to shelf
3
Shelf to controller
2
Shelf to shelf
PSU PSU
DS14
IN
OUT
IN OUT
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
FAS2020
0a e0a e0b0b
Controller Module B
0a e0a e0b0b
10101
10101
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
FAS2020
0a e0a e0b0b
Controller Module B
0a e0a e0b0b
10101
10101
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
FAS2020
0a e0a e0b0b
Controller Module B
0a e0a e0b0b
10101
10101
Controller to shelves
Single Controller Dual Path
1
Controller to shelf
DS14
DS14
PSU
PSU
PSU
PSU
PSU PSU
FAS2020
0a e0a e0b0b
10101
INOUT
INOUT
IN
OUT
IN OUT
IN
Active/Active FC SAN Dual Path
1
2
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
FAS2020
0a e0a e0b0b
Controller Module B
0a e0a e0b0b
10101
10101
PSU PSU
DS14
IN
OUT
IN OUT
PSU PSU
DS14
INOUT
IN OUT
PSU PSU
FAS2020
0a e0a e0b0b
Controller Module B
0a e0a e0b0b
10101
10101
Connect power
3U
3U
2U
1
1
(2x)
FRONT SIDE
(2x)
Front rail
(2x)
Clip nut (4x)
Controller to switch
e0be0a0a 0b
8
8
e0be0a0a 0b
8
Note: You do not need to
ground your system.
Trim-17” x 22”

NetApp FAS2020 Specifications

General

Brand	NetApp
Model	FAS2020
Category	Storage
Language	English

Summary

Before You Begin

Unpack and Verify Contents

Install in Rack

Cable the System

Cable Controllers

Connect console cable and network cables to controller ports.

Cable Disk Shelves

Configure disk shelf IDs and connect disk shelves to controllers.

Connect Power

Connect power cables to the system.

Boot the System and Proceed with Setup

Hardware Overview of the FAS2020 System

Appliance Rear Components

Identify components on the rear of the FAS2020 appliance.

Appliance Front Components

Identify components on the front of the FAS2020 appliance.

Shutting Down a Controller Module

Active/Active Configuration Shutdown

Steps for shutting down a controller in an active/active setup.

Single-Controller Configuration Shutdown

Steps for shutting down a controller in a single-controller setup.

Opening and Closing the System

Opening the System

Procedure for safely removing a controller module from the system.

Closing the System

Procedure for installing a controller module back into the system.