Need help?Do you have a question about the NETGEAR GS110EMX and is the answer not in the manual?
General| Switch type | Managed |
|---|---|
| Switch layer | L2/L3 |
| Quality of Service (QoS) support | Yes |
| Number of VLANs | 64 |
| Networking standards | IEEE 802.1Q, IEEE 802.1p, IEEE 802.3az, IEEE 802.3x |
| Virtual LAN features | Voice VLAN, Tagged VLAN, Port-based VLAN |
| Cable types supported | Cat5, Cat5e, Cat6, Cat6a, Cat7 |
| DHCP features | DHCP client |
| Queue scheduling algorithms | Weighted Round Robin (WRR) |
| Noise level | 0 dB |
| Power connector | DC-in jack |
| Installed SFP modules quantity | 0 |
| Gigabit Ethernet (copper) ports quantity | 8 |
| Basic switching RJ-45 Ethernet ports type | Gigabit Ethernet (10/100/1000) |
| Basic switching RJ-45 Ethernet ports quantity | 10 |
| Jumbo frames | 10240 |
| Forwarding rate | 41.664 Mpps |
| Latency (1 Gbps) | 4 µs |
| Latency (10 Gbps) | 3 µs |
| MAC address table | 16000 entries |
| Packet buffer memory | 0.128 MB |
| Latency (10-100 Mbps) | 7 µs |
| Number of multicast groups filtered | 128 |
| Safety | UL/cUL Listed (UL 60950-1)/CAN/CSA C22.2 No. 60960-1-07, EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, IEC 60950-1:2005 (ed.2)+A1:2009+A2:2013, AS/NZS 60950.1:2015 |
| Stackable | - |
| Certification | 47 CFR FCC Part 15, SubpartB, Class B ICES-003:2016 Issue 6, Class B ANSI C63.4:2014 N 55032:2012 +AC:2013 / CISPR 32:2012 / AS/NZS CISPR 32:2013, Class B EN 55032:2015 +AC:2016 / CISPR 32:2015 +COR1:2016 / AS/NZS CISPR 32:2015, Class B EN 61000-3-2:2014 EN 61000-3-3:2013 EN 55024:2010 +A1:2015 |
| Product color | Black |
| LED indicators | Link, Power, Speed |
| Number of fans | 0 fan(s) |
| Housing material | Metal |
| Electromagnetic compatibility | Class B |
| Output current | 2.5 A |
| Output voltage | 12 V |
| Power consumption (max) | 15.6 W |
| Power consumption (typical) | 6.6 W |
| Heat dissipation | 53.35 BTU/h |
| Operating altitude | 0 - 3000 m |
| Storage temperature (T-T) | -20 - 70 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Storage relative humidity (H-H) | 0 - 95 % |
| Operating relative humidity (H-H) | 0 - 90 % |
| Package depth | 270 mm |
| Package width | 164 mm |
| Package height | 85 mm |
| Package weight | 1340 g |
| Shipping (inner) case width | 490 mm |
| Shipping (inner) case height | 339 mm |
| Shipping (inner) case length | 391 mm |
| Shipping (inner) case net weight | 15460 g |
| Number of layers per pallet (air) | 4 pc(s) |
| Number of cartons per pallet layer | 6 pc(s) |
| Quantity per shipping (inner) case | 10 pc(s) |
| Harmonized System (HS) code | 85176990 |
Weight and Dimensions| Depth | 102 mm |
|---|---|
| Width | 236 mm |
| Height | 27 mm |
| Weight | 750 g |
Provides essential safety guidelines to prevent injury and equipment damage.
Guides on physically setting up the switch and powering it on.
Steps to assign a fixed IP address for consistent access.
Steps to change the default switch password for security.
Guides on creating simple VLANs by assigning ports to VLANs.
Basic setup for creating VLANs using the 802.1Q standard.
Advanced setup for 802.1Q VLANs with tagging and PVID.
Enabling QoS based on packet header priority information.
Setting QoS priorities on a per-port basis for traffic management.
Configuring static or DHCP IP addresses for the switch.
Combining multiple Ethernet links into a single logical link.
Activating the switch's loop prevention feature to avoid network loops.
Steps to manually download and install new firmware for the switch.
Saving and restoring the current switch configuration to a file.
Erasing current settings and returning the switch to factory defaults.
To Next Page
