NETGEAR ProSAFE WN203 User Manual

4
ProSAFE Single Band 802.11n Wireless Access Point WN203
Schedule the Wireless Radios to Be Turned Off . . . . . . . . . . . . . . . . . . . .49
Configure Basic Wireless Quality of Service . . . . . . . . . . . . . . . . . . . . . . .49
Chapter 4 Management
Enable Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
SNMP Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Secure Shell and Telnet Management . . . . . . . . . . . . . . . . . . . . . . . . . .53
Upgrade the Wireless Access Point Software . . . . . . . . . . . . . . . . . . . . . .54
Web Browser Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
TFTP Server Upgrade Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Manage the Configuration File or Reset to Factory Default . . . . . . . . . . . .57
Save the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Restore the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Restore the Wireless Access Point to the Factory Default Settings. . . .58
Reboot the Wireless Access Point without Restoring the
Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Change the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Enable the Syslog Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Enable Rogue AP Detection and Monitor Access Points. . . . . . . . . . . . . .62
Enable and Configure Rogue AP Detection . . . . . . . . . . . . . . . . . . . . . .63
View and Save Access Point Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Chapter 5 Advanced Configuration
Configure Spanning Tree Protocol and 802.1Q VLANs. . . . . . . . . . . . . . .68
Configure Hotspot Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Configure Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Configure Advanced Quality of Service Settings . . . . . . . . . . . . . . . . . . . .73
Configure Wireless Bridging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Configure a Point-to-Point Wireless Network . . . . . . . . . . . . . . . . . . . . .76
Configure a Point-to-Multipoint Wireless Network . . . . . . . . . . . . . . . . .81
Configure the Wireless Access Point to Repeat the Wireless
Signal Using Point-to-Multipoint Bridge Mode . . . . . . . . . . . . . . . . . . . .85
Chapter 6 Monitoring
View System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Monitor Wireless Clients. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
View the Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Traffic Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Chapter 7 Troubleshooting
Basic Functioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Verify the Correct Sequence of Events at Startup . . . . . . . . . . . . . . . .100
No LEDs Are Lit on the Wireless Access Point . . . . . . . . . . . . . . . . . .100
LAN LED Is Not Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
WLAN LED Is Not Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
You Cannot Access the Internet or the LAN from a

NETGEAR ProSAFE WN203 Specifications

General

Brand	NETGEAR
Model	ProSAFE WN203
Category	Wireless Access Point
Language	English