Netum NT-W6 User Manual

NT-W6
Quick Setup Guide
This model can work both via USB cable or 2.4G receiver.
Connection Mode
Working via USB cable
Get Started: Connect scanner with your device via USB cable. If you use US keyboard, it's a plug and play
model. If you use other type of keyboard , please refer to below "keyboard language type" to set the
keyboard language before use it. If you use it on MAC system you have to plug a 2.4G receiver working
under wireless mode.
Working via 2.4G receiver
Get Started: Plug the 2.4G receiver on your device, then you can start to use it. (US keyboard by default) If
you use other type of keyboard , please refer to below "keyboard language type" to set the keyboard
language before use it.
Low voltage Alarm: Scanner will make 3x beeps (even you just trigger the button and do not scan any
barcodes) to remind you that it's under low voltage. Please plug the USB cable to charge power for it.
If you want to do other configurations please refer to below programming barcodes.
Firmware Version:
Read below command barcode to check scanner firmware version.
Firmware Version
Below programming barcodes are applied for version - 2.4GWISX_20180412
Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar codes in
this guide. An asterisk (*) next to an option indicates the default setting.
Important Note: There will not have a beep sound for some of configuration .As long as light turns off a
few seconds before you release the trigger button that means scanner has read the codes successfully.

Netum NT-W6 Specifications

General

Connectivity	Bluetooth
Scanning Speed	300 scans/sec
Supported Barcode Types	Code 39, Code 128
Operating Range	100 meters
Scanning Distance	5-30cm
Interface	USB

Summary

Quick Setup Guide

Connection Mode

Defines how the scanner connects via USB cable or 2.4G receiver.

Working via USB cable

Connect scanner via USB cable for plug-and-play or custom setup.

Working via 2.4G receiver

Plug in the 2.4G receiver to connect the scanner wirelessly.

Firmware Version

Read barcode to check the scanner's current firmware version.

Barcode Programming

Use programming barcodes to change scanner settings and configurations.

Keyboard Language Type

USA Keyboard

Set scanner for US keyboard layout, default for plug-and-play.

French Keyboard

Set scanner for French keyboard layout for correct code transmission.

Scanning Mode

Trigger Mode (Default)

Enables manual trigger mode, allowing scanning only when the trigger is pressed.

Continuous Mode

Continuous Scanning

Scanner continuously scans and transmits data repeatedly without manual trigger.

Working Mode

Offline Mode

Activates offline mode to store scanned data in buffer memory when out of signal range.

Clear all Storage

Scan to delete all data currently stored in the buffer memory.

Terminator Settings

CR* (Carriage Return)

Sets the terminating character suffix to Carriage Return (CR).

CR+LF (Carriage Return + Line Feed)

Sets the terminating character suffix to CR+LF.

Factory Restore Process

Step 1 Factory Restore

Resets the scanner to its original factory default settings.

Step 5 Setting Channel

Configures the communication channel for the scanner.

EAN Barcode Symbologies

Enable EAN-8*

Enables the EAN-8 barcode symbology for scanning.

Enable EAN-13*

Enables the EAN-13 barcode symbology for scanning.

EAN-13 to ISBN Transfer

Enable EAN-13 Transfer to ISBN

Allows conversion of EAN-13 barcodes to ISBN format upon scanning.

EAN-13 to ISSN Transfer

Enable EAN-13 Transfer to ISSN

Allows conversion of EAN-13 barcodes to ISSN format upon scanning.

Codabar Symbology

Enable Codabar*

Enables the Codabar barcode symbology for scanning.

Code 39 Symbology

Enable Full ASCII*

Enables the Full ASCII character set for Code 39 barcodes.

Code 93 Symbology

Enable Code 93*

Enables the Code 93 barcode symbology for scanning.

Code128 Symbology

Enable Code 128*

Enables the Code 128 barcode symbology for scanning.

GS1 DataBar Limited (RSS Limited)

Enable RSS Limited

Enables the GS1 DataBar Limited (RSS Limited) barcode symbology.

UPC-A Symbology

Enable UPC-A *

Enables the UPC-A barcode symbology for scanning.

UPC-A to EAN-13 Transfer

Enable UPC-A Transfer to EAN-13

Allows conversion of UPC-A barcodes to EAN-13 format upon scanning.

UPC-E Symbology

Enable UPC-E

Enables the UPC-E barcode symbology for scanning.

Add-On Code Settings

Enable 2-Digit Add-On Code

Enables the use of 2-digit add-on codes for EAN/UPC barcodes.

Enable 5-Digit Add-On Code

Enables the use of 5-digit add-on codes for EAN/UPC barcodes.

UPC-E to UPC-A Transfer

Enable Transfer UPC-E to UPC-A

Allows conversion of UPC-E barcodes to UPC-A format upon scanning.

Interleaved 2 of 5 Symbology

Enable Interleaved 2 of 5*

Enables the Interleaved 2 of 5 barcode symbology for scanning.

Standard 2 of 5 Symbology

Enable Standard 2 of 5

Enables the Standard 2 of 5 barcode symbology for scanning.

Matrix 2 of 5 Symbology

Enable Matrix 2 of 5*

Enables the Matrix 2 of 5 barcode symbology for scanning.

MSI Symbology

Enable MSI

Enables the MSI barcode symbology for scanning.

Custom Prefix And Suffix

Custom Prefix

Configures a custom prefix to be added to all scanned data.

Scan Data Transmission Format

$DATA#0 *Data As Is

Sets the data transmission format to send scanned data exactly as is.

Scan Data Transmission Formats

$DATA#0 *Data As Is

Sets the data transmission format to send scanned data exactly as is.

$DATA#1 <DATA><SUFFIX 1>

Sets data transmission to append Suffix 1 to scanned data.

$DATA#4 <PREFIX> <DATA >

Sets data transmission to prepend a Prefix to scanned data.

$DATA#7 <PREFIX> <DATA> <SUFFIX 1> <SUFFIX 2>

Sets data transmission with Prefix, Suffix 1, and Suffix 2.

Numeric Bar Codes

$NO#0

Numeric barcode representing the value 0 for parameter settings.

$NO#5

Numeric barcode representing the value 5 for parameter settings.

$NO#9

Numeric barcode representing the value 9 for parameter settings.

Keystroke and Functional Key Sets

Enable Keystroke*

Enables the direct mapping of scanned values to keystrokes.

Enable functional Key Set

Enables mapping of scanned values to specific functional key sets like Ctrl+D.

Full ASCII Code 39