20-Aug-12
4
Introduction (Continued)
Number of Brews
– The number of brew cycles started may be tracked with this feature. The accumulated number of cycles
may be reset. Using the brew buttons, first display “Cir” when in the program mode, and then depress cancel.
Power Mode
– Allows you to automatically save energy when the brewer is not in use for a length of time specified under power
shutdown time. Available modes are: normal, power save (standby) and power down. The modes are described below.
• Normal – In this mode the tank temperature will be maintained at the preset temperature at all times.
• Power Save (Standby) – In this mode the tank temperature will be maintained at approximately 170 degrees when the set
time has been reached. Brew 1 light will flash about once every 10 seconds to indicate unit is in power save mode.
• Power Down – In this mode the tank heater element will be disabled when the set time has been reached. Brew 2 light will
flash about once every 10 seconds to indicate unit is in power down mode.
Sequence Of Programming Steps For Single Barista Controller
• Depress and hold Cancel button until display lights up. (Approximately 10 seconds).
• You are now in the Program Mode. Functions to be programmed appear in the order in which they are shown in the
following table.
• Use the Cancel button to cycle through the functions to find the one you wish to change.
• Use the Brew 1 button to lower the displayed value (-) and the Brew 2 button to raise the value (+). Press Cancel to store
the changed value and advance to the next function.
• If the brewer detects no activity for approx. 60 seconds it will exit out the Program Mode, except as noted below.
Code Function To Set Set Values Available Lights Icon Adjacent To
1A Brew 1 time OFF, 30 ounces – 255 ounces Brew 1
1b Brew 2 time OFF, 30 ounces – 255 ounces Brew 2
2a Dual volume – brew 1 Double dump feature ON or OFF Water filtering Brew 1
2b Dual volume – brew 2 Double dump feature ON or OFF Water filtering Brew 2
3 Visa-brew time OFF, 30 second – 2.5 minutes Brew 1 & Brew 2 (both flashing)
4 Water Temp. 1 170 F – 205 F Service
5 Auto Arm ON or OFF Heating (flashing)
6A Pre-infusion 1 mode ON or OFF Brew 1 (pulsing) Coffee Monitor
6b Pre-infusion 2 mode ON or OFF Brew 2 (pulsing) Coffee Monitor
7 Pulse brew mode ON or OFF Brew 1 & Brew 2 (pulsing)
7A Pulse brew 1 time 2 0 seconds – 60 seconds Brew 1 (pulsing)
7b Pulse brew 1 time 3 0 seconds – 60 seconds Brew 2 (pulsing)
8A Audible alert mode ON or OFF None
8b Audible alert # of beeps Off, 1 – 9 None
9 Coffee freshness monitor 10 minutes – 2 hours Coffee Monitor
10A Filtering flow rate OFF, 0.25 – 1.00 GPM Water Filtering
10b Filter capacity 4 OFF, 0.50 – 2.50 gal. X 100 Water Filtering (flashing)
11 Number of brews Quantity, Cir Brew 1 & Brew 2
13A Power Mode Normal, Power Save, Power Down None (Displayed: P:n, P:s & P:d)
13b Power shutdown time 5 30 minutes – 4 hours None
End None 6 N/A None
1. Brewer will remain in this sequence indefinitely until Cancel button is pressed. Heating icon will track heater operation.
2. Hidden if pulse brew mode is off or Brew 1 time is off.
3. Hidden if pulse brew mode is off or Brew 2 time is off.
4. Hidden if filter flow rate is off.
5. Hidden when power save mode is normal.
6. Program mode will time out in 15 seconds at end of programming sequence.
To Next Page
Loading...
