How to fix garbled data with RS232 on Newland NLS-HR200 Barcode Reader?
If you're receiving garbled data with RS232 on your Newland Barcode Reader, the baud rate settings between the scanner and the host might be inconsistent. Ensure that the baud rate settings for both the scanner and the PC-side communication port are the same.
What to do if Newland NLS-HR200 Barcode Reader does not read barcodes?
If your Newland Barcode Reader isn't reading barcodes, the issue might be that the barcode type is not enabled. Please enable the barcode type in the scanner settings. If the scanner firmware doesn't support reading the barcode, contact your dealer or us for assistance.
Why my Newland NLS-HR200 Barcode Reader does not turn on?
If your Newland Barcode Reader isn't turning on, it could be due to a connection issue. Here are a few things to check: * **RS232 Communication:** Ensure the adapter is properly inserted. * **Communication Interface:** Verify the communication port is correctly connected, whether you're using RS232, USB, or PS/2 communication.
Provides an overview of the user guide content and purpose.
Details the content covered in each chapter of the manual.
Explains the meaning of symbols and icons used throughout the manual.
Introduces the HR200 barcode scanner and its capabilities.
Instructions for unpacking the HR200 scanner and accessories.
Diagram showing the major components of the HR200 scanner.
Defines the pinout for the HR200R model's interface.
Defines the pinout for the HR200P model's interface.
Explains power on/off states, idle mode, and restart procedures.
Provides instructions for cleaning and maintaining the scanner.
Step-by-step guide for scanning barcodes in hand-held mode.
Instructions for using the scanner with a stand in hands-free mode.
Introduces Code, Command, and QuickSet programming methods.
Explains programming using special barcodes.
Explains programming using Pro CMD strings.
Explains programming using the QuickSet GUI software.
Enables/disables decoding beep and selects beep type.
Adjusts beep volume and configures power-on beep.
Explains the meaning of different beep patterns.
Resets all scanner parameters to factory defaults.
Saves and loads custom user-defined settings.
Sets the data transmission speed for RS232.
Configures the parity check settings for RS232 communication.
Enables or disables hardware flow control for RS232.
Sets the number of data bits for RS232 transmission.
Sets the stop bit configuration for RS232 transmission.
Explains the Newland-developed DataPipe USB protocol.
Explains the HID-KBW USB protocol for keyboard emulation.
Configures keyboard layouts and country codes for HID-KBW.
Configures how unknown characters are handled, with optional beeps.
Enables sending full ASCII characters via the numeric keypad.
Sets the delay in milliseconds between emulated keystrokes.
Controls the behavior of the Caps Lock key for data input.
Methods for accessing the device and getting scanned data programmatically.
Details the format of data received after scanning.
Lists Vendor ID and Product ID for device identification.
Enables or disables reading of all barcode types.
Enables or disables reading of all 2D barcode types.
Loads factory defaults and enables/disables Code 128 symbology.
Sets the minimum and maximum message length for Code 128.
Loads factory defaults and enables/disables EAN-8 symbology.
Configures check digit and addenda codes for EAN-8.
Enables expansion of EAN-8 barcodes to EAN-13 format.
Loads factory defaults and enables/disables EAN-13 symbology.
Configures check digit and addenda codes for EAN-13.
Loads factory defaults and enables/disables UPC-E symbology.
Configures check digit and addenda codes for UPC-E.
Controls the transmission of the default '0' for UPC-E.
Enables expansion of UPC-E barcodes to UPC-A format.
Loads factory defaults and enables/disables UPC-A symbology.
Configures check digit and addenda codes for UPC-A.
Controls the transmission of the default '0' for UPC-A.
Loads factory defaults and enables/disables Interleaved 2 of 5.
Sets the minimum and maximum message length for Interleaved 2 of 5.
Configures check digit handling for Interleaved 2 of 5.
Configures specific length reading for Interleaved 2 of 5.
Enables or disables the ITF-14 barcode symbology.
Configures check digit transmission for ITF-14.
Enables or disables the ITF-6 barcode symbology.
Configures check digit transmission for ITF-6.
Loads factory defaults and enables/disables Code 39 symbology.
Configures the start and stop characters for Code 39.
Sets the minimum and maximum message length for Code 39.
Configures check digit handling for Code 39.
Enables full ASCII character decoding for Code 39.
Loads factory defaults and enables/disables Codabar symbology.
Sets the minimum and maximum message length for Codabar.
Configures check digit handling for Codabar.
Configures start and stop characters for Codabar.
Loads factory defaults and enables/disables Code 93 symbology.
Sets the minimum and maximum message length for Code 93.
Configures check digit handling for Code 93.
Loads factory defaults and enables/disables UCC/EAN-128 symbology.
Loads factory defaults and enables/disables GS1 Databar symbology.
Configures the transmission of the AI(01) character for GS1 Databar.
Loads factory defaults and enables/disables EAN·UCC Composite.
Loads factory defaults and enables/disables Code 11 symbology.
Sets the minimum and maximum message length for Code 11.
Configures check digit handling for Code 11.
Loads factory defaults and enables/disables ISBN symbology.
Configures ISBN transmission for 10 or 13 digits.
Loads factory defaults and enables/disables Industrial 25 symbology.
Sets the minimum and maximum message length for Industrial 25.
Configures check digit handling for Industrial 25.
Loads factory defaults and enables/disables Standard 25 symbology.
Sets the minimum and maximum message length for Standard 25.
Configures check digit handling for Standard 25.
Loads factory defaults and enables/disables Plessey symbology.
Sets the minimum and maximum message length for Plessey.
Configures check digit handling for Plessey.
Loads factory defaults and enables/disables MSI-Plessey symbology.
Sets the minimum and maximum message length for MSI-Plessey.
Configures check digit handling for MSI-Plessey.
Loads factory defaults and enables/disables PDF417 symbology.
Sets the minimum and maximum message length for PDF417.
Configures reading options for PDF417 twin codes.
Configures forward/positive direction and mirror image reading.
Loads factory defaults and enables/disables QR Code symbology.
Sets the minimum and maximum message length for QR Code.
Configures reading options for QR Code twin codes.
Loads factory defaults and enables/disables Aztec symbology.
Sets the minimum and maximum message length for Aztec.
Configures reading modes for multiple barcodes.
Sets the number of barcodes to read in multi-barcode mode.
Loads factory defaults and enables/disables Data Matrix symbology.
Sets the minimum and maximum message length for Data Matrix.
Configures reading options for Data Matrix twin codes.
Configures handling for rectangular Data Matrix symbols.
Configures forward/positive direction and mirror image reading.
Loads factory defaults and enables/disables Maxicode symbology.
Sets the minimum and maximum message length for Maxicode.
Explains Optical Character Recognition and supported standards.
Explains how Prefix and Suffix are used to modify barcode messages.
Enables or disables the use of prefix and suffix.
Explains how to set and customize Code ID prefixes.
Instructions to modify Code IDs for 2D barcodes like PDF417, QR Code, etc.
Instructions to modify Code IDs for 1D barcodes like EAN-8, UPC-A, etc.
Instructions to modify Code IDs for ITF-6, Code 39, Codabar, Code 93.
Instructions to modify Code IDs for Code 128, ISBN, GS1 Databar, etc.
Enables or disables the appending of a user-defined suffix.
Enables or disables the use of a stop suffix.
Explains message interception for selected barcode sections.
Covers disabling, enabling, and programming interception options.
Controls the data packing feature for barcode messages.
Explains how to integrate programming sequences into a single barcode.
Provides instructions on how to use digit codes for programming.
Explains how to save received data after transmission.
Describes how to abort current data or settings.
General| Brand | Newland |
|---|---|
| Model | NLS-HR200 |
| Category | Barcode Reader |
| Language | English |
To Next Page
