To Next PageTo Next PageWhat to do if Nilfisk-Advance Floor Machine wheel drive works in one direction only?
If the wheel drive on your Nilfisk-Advance Floor Machine only works in one direction, you should repair the wiring or replace the R1 pot and replace the (A1) speed control.
Why won't the wheel drive motor run in forward and reverse on my Nilfisk-Advance Floor Machine?
Several factors can prevent the wheel drive motor from running in both directions. Here's what to check: * **Batteries:** Ensure they are fully charged and recharge if necessary. * **Circuit Breakers:** Look for tripped breakers, specifically the Wheel Drive Motor Circuit Breaker (F2) and the Control Circuit Breaker (F4), and reset them. * **Parking Brake:** Make sure the parking brake is released. * **Emergency Stop Switch:** Verify the Emergency Stop Switch (13) is not tripped; reconnect the battery to reset it. * **Safety Switch:** Check the Safety Switch (S2) in the seat to confirm it's closed. * **Motor:** The Wheel Drive Motor might be defective and need replacement. * **Throttle Potentiometer:** A defective Throttle Potentiometer (R1) may also be the cause, requiring ...
Warns of immediate hazards causing severe personal injury or death.
Warns of situations that could cause severe personal injury.
Warns of situations that could cause minor injury or damage to the machine.
Provides general safety guidelines for machine operation and maintenance.
Offers specific cautions regarding machine use, public paths, hazardous dust, etc.
Lists physical dimensions, capacities, performance data, and component specifications.
Provides detailed specifications based on machine deck size (24", 26", 28", 32").
Lists operational checks to be performed during routine maintenance.
Lists visual checks for components during routine maintenance.
Details the function of each switch and indicator on the machine's control panel.
Explains the operation of specific control buttons like Scrub Off and Speed Select.
Describes the meaning of various status lights on the control panel.
Explains the battery condition indicator lights and voltage ranges.
Describes the display's use for hourmeter, error codes, and settings.
Describes the 36V motor/gear transmission and the speed controller.
Explains the controller's operational circuit and inputs.
Details the two operating modes for the speed controller.
Explains how the speed select switch affects the controller's output.
Provides common problems and their possible causes for the wheel drive system.
Guides troubleshooting of scrub system failures using error codes.
Troubleshooting guide for squeegee lift motor issues.
Introduces methods for diagnosing issues with the Curtis speed controller.
Provides safety warnings and steps for installing batteries.
Provides steps and warnings for charging the machine's batteries.
Offers rules for maintaining battery life: electrolyte level, charging, and cleaning.
Procedure for checking the speed controller installation before operation.
Provides the wiring diagram for machines before a specific serial number.
Provides the wiring diagram for machines after a specific serial number.
Describes methods for testing batteries and identifying dead cells.
Explains how error codes are displayed and used for troubleshooting.
Lists error codes for drive system, lift actuators, and scrub motor.
Warns of immediate hazards causing severe personal injury or death.
Warns of situations that could cause severe personal injury.
Warns of situations that could cause minor injury or damage to the machine.
Provides general safety guidelines for machine operation and maintenance.
Offers specific cautions regarding machine use, public paths, hazardous dust, etc.
Lists physical dimensions, capacities, performance data, and component specifications.
Provides detailed specifications based on machine deck size (24", 26", 28", 32").
Lists operational checks to be performed during routine maintenance.
Lists visual checks for components during routine maintenance.
Details the function of each switch and indicator on the machine's control panel.
Explains the operation of specific control buttons like Scrub Off and Speed Select.
Describes the meaning of various status lights on the control panel.
Explains the battery condition indicator lights and voltage ranges.
Describes the display's use for hourmeter, error codes, and settings.
Describes the 36V motor/gear transmission and the speed controller.
Explains the controller's operational circuit and inputs.
Details the two operating modes for the speed controller.
Explains how the speed select switch affects the controller's output.
Provides common problems and their possible causes for the wheel drive system.
Guides troubleshooting of scrub system failures using error codes.
Troubleshooting guide for squeegee lift motor issues.
Introduces methods for diagnosing issues with the Curtis speed controller.
Provides safety warnings and steps for installing batteries.
Provides steps and warnings for charging the machine's batteries.
Offers rules for maintaining battery life: electrolyte level, charging, and cleaning.
Procedure for checking the speed controller installation before operation.
Provides the wiring diagram for machines before a specific serial number.
Provides the wiring diagram for machines after a specific serial number.
Describes methods for testing batteries and identifying dead cells.
Explains how error codes are displayed and used for troubleshooting.
Lists error codes for drive system, lift actuators, and scrub motor.
General| Brand | Nilfisk-Advance |
|---|---|
| Model | BR 700S |
| Category | Floor Machine |
| Language | English |
