Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
RF Information
1. Frequency band(s): 2415~2459MHz
2. Receiver category: Category 2
3. Maximum Transmit Power EIRP (mW): 100 mW
4. EU declaration;
EN 300 328 V2.1.1(2016-11)
EN 301 489-1 V2.1.1(2017-02)
EN 301 489-17 V3.1.1(2017-02)
EN 55032:2015 +AC:2016, Class B
EN 61000-3-2:2014(Not Applicable)
EN 61000-3-3:2013(Not Applicable)
EN 61000-4-2:2009
EN 61000-4-3:2006 +A1:2008 +A2:2010
Page 09/09
ItemNO. Specification
3.7V,3000mAh,18650 Li-ion battery cell x2 parallelPower source
Battery operating voltage range
Radio type
Motor type
Interface
Charge type
Charge capability
USB
USB
Solar
Solar
Charge
Discharge
Charge time
@ 3000mAh battery cell x2
Thermal protection
Dust and Water proof
Operation temperature
1
2
3
4
5
6
7
8
9
10
11
4.2V~3.2V
Proprietary 2.4G RF
Brush DC motor
USB micro B receptor(water proof)
USB, Solar
4W(5V, 0.8A)
0.06W@37000lux(5V,12mA)
10hrs
300hr@37000lux
H:≥60°C
L:≤0°C
H:≥60°C
L:≤-10°C
IP54
0°C~55°C
MS4 Motor Module specification:
˙Caution
1. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction. Children being supervised not to play with the
appliance.
2.The battery must be removed from the appliance before it is scrap; The appliance must be disconnected from the supply
mains when removing the battery; The battery is to be disposed of safely.
3. Do not allow children to play with fixed controls. Keep remote controls away from children;
4. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or
adjustment is necessary
5. Do not operate when maintenance, such as window cleaning, is being carried out in the vicinity;
6. Before installing the drive, remove any unnecessary cords or components and disable any equipment not needed for powered
operation; That the characteristics of the driven part must be compatible with the rated load and rated operating time.
To Previous Page
Loading...
