5、Safety Instructions
The PerfectTilt
™
Motor Module and Remote (SmartDial
™
) contain lithium batteries, the battery contains flammable
materials such as organic solvents. Mishandling the battery may cause fire, smoke, or an explosion and the battery’s
functionality will be seriously damaged. Please read and check the following prohibited actions. [NOTE: The Remote
batteries (CR2032) is not rechargeable.]
˙Danger
(1) Immersion
Do not immerse the battery in liquid such as water, beverages, or other fluids.
Exposure to liquid may damage the battery or the battery pack (including protection circuit). As a result, the battery may generate heat, smoke, catch
fire, or explode.
(2) High Temperature
Do not use or place the battery near an open flame, heater or high temperature (above 80°C).
Subjecting the battery to high temperature may damage the polyolefin separator and can cause an internal short circuit. This may cause the battery to
generate heat, smoke, catch fire, or explode.
(3) Chargers and Charge Conditions
Do not use unauthorized chargers.
Only charge the battery within specified conditions (e.g., temperature range, voltage, and current). Use of an unauthorized charger could cause the
battery to generate heat, smoke, catch fire, or explode.
(4) Reverse Polarity
Do not attach or insert battery with polarity reversed.
A battery has polarity. If the battery does not easily fit into the charger or device, check the battery’s orientation. Do not force the battery into the
battery compartment. If attached to the device with reversed polarity, the battery may generate heat, smoke, catch fire, or explode.
(5) Direct Connection
Do not connect the battery to an AC outlet or DC automotive plug.
The battery requires a specific charger. If the battery is connected directly to a power outlet, the battery may generate heat, smoke, catch fire, or
explode.
(6) Use in Other Equipment
Do not use the battery in equipment for which it was not intended.
If the battery is used in unapproved applications or systems, the battery may become damaged and generate heat, smoke, catch fire, or explode.
(7) Incineration and Heat
Keep the battery away from heat and fire.
Heat will damage the battery and may cause it to generate heat, smoke, catch fire, or explode.
(8) Short-Circuit
Do not apply a short-circuit.
Do not connect the positive (+) and negative (-) terminals with a conductive material. Do not carry or store the battery with any metal
objects. If the battery is shorted, the shorting item may overheat and the battery may generate heat, smoke, catch fire, or explode.
(9) Impact
Avoid excessive impact to the battery.
Impact beyond specification may damage the battery. This may cause the battery to leak, generate heat, smoke, catch fire, or explode.
(10) Penetration
Do not penetrate the battery with a nail or strike with a hammer.
If subjected to a hard strike or penetrated by an object, the battery may be damaged or destroyed, thereby causing an internal short-circuit.
This may cause the battery to generate heat, smoke, catch fire, or explode.
(11) Soldering
Do not directly solder to the battery.
Soldering directly to the battery could melt the separator or damage the gas release vent or other safety mechanisms. This may cause the
battery to generate heat, smoke, catch fire, or explode.
(12) Disassembly
Do not disassemble the battery.
Disassembly or modification of the battery may damage the protection circuit. This may cause the battery to generate heat, smoke, catch
fire, or explode.
(
(13) Charge near High Temperatures
Do not charge the battery near high temperature.
If the battery is charged while exposed to high temperature, the battery’s protection circuit may activate and prevent charging, or fail and
cause the battery to generate heat, smoke, catch fire, or explode.
Pack the battery securely for transport.
To prevent short-circuit or damage during transport, securely pack the battery in a case or carton.
Page 07/09
IssuesNO. Troubleshooting
1. Check if the Norman
®
Hub has a network route or WiFi connection to the home AP router? If the
Norman
®
Hub is not connected to the home AP router, you can find the SSID of the
NORMANHUB_OOOOOO via the WiFi settings of the phone.
2. If you can find the NORMANHUB_OOOOOO SSID, connect to this WiFi and open the App, then go to
Connect to Hub > Menu > Hub Info > Home AP Settings and follow the instructions to connect the
Norman
®
Hub to your home AP router.
3. If you can't find the SSID of NORMANHUB_OOOOOO, please reboot the Norman
®
Hub and try to
connect it again through the App.
4. If none of the above steps can be resolved, manually switch Norman
®
Hub to AP mode. Press the
router button for 3 seconds to enter the User Setting Mode. At this time, the blue light will be on
constantly. Press 2 times within 5 seconds in the User Setting Mode and go to step 2.
5. Some AP routers will automatically enable the Multicast Filter function. Please log in to the home
AP router to enter the setting page and turn off the Multicast Filter function. (The setting method of
each brand may be different, please refer to the manual of each brand)
App can't
connect to
Norman
®
Hub
3
To Next Page
Loading...