Why does my Oki Printer have odours?
If your Oki Printer is emitting odours, it is because gases are being released by forms or adhesives as they pass through the hot fusing unit. Ensure that the forms you use can withstand heating, and provide adequate ventilation to dissipate the odours.
How to fix FEED JAM or EXIT JAM on Oki B4250 Printer?
To resolve a FEED JAM or EXIT JAM on your Oki Printer, first remove the tray and clear any misfed sheets. Then, open the top cover and carefully lift out the image drum along with the toner cartridge. Remove any jammed sheets from the paper path. Re-install the image drum with the toner cartridge, and close the top cover securely. The printer will warm up and begin printing when ready. If the edge of the jammed paper protrudes, remove the jammed paper from the exit when the exit roller begins rotating after a few seconds after switching on.
Why is the print faded on my Oki Printer?
If your Oki Printer is printing faded, it could be due to a few reasons. First, ensure the toner cartridge is correctly installed. If it is, the toner might be low. In that case, replace the toner cartridge.
What to do if Oki B4250 is printing blank sheets?
If your Oki Printer is printing blank sheets, it might be due to the image drum cartridge not being properly installed. Try reinstalling the image drum cartridge. Another possible cause is an empty or missing toner cartridge, so install a new toner cartridge if needed.
Why does my Oki Printer print entire page faintly?
If the entire page prints faintly on your Oki Printer, it's likely due to an empty toner cartridge. As the toner is used up, pages will appear fainter. Install a new toner cartridge to resolve this. Alternatively, the LED array might be dirty; in this case, clean the LED array.
Why does my Oki Printer print a graphic image on multiple pages?
If a graphic image prints partly on one page and partly on the next with your Oki Printer, it indicates that there is insufficient printer memory for this image at the current resolution. Try changing the resolution, reducing the image size, or installing more memory in your printer.
Why does the top margin increase with each page on my Oki B4250?
If the size of the top margin increases with each page printed from your Oki Printer, it is due to creeping text. This occurs when the number of lines per page in your software does not match the number of lines per page set on the printer. Adjust your software accordingly, or set the LINES Per PAGE in the soft control panel to match the lines per page in your software.
Why does my Oki Printer need to warm up before printing?
If your Oki printer is on but must warm up before a job is printed, Power Save mode is likely enabled to conserve energy. The fuser needs to heat up before printing the next job. To eliminate this warm-up delay, change the Power Save setting.
What to do if Oki B4250 Printer is ready but not printing?
If you try to print and nothing happens, but your Oki Printer indicates it is ready to receive data, there may be a configuration error. Check the cable connection to ensure it is secure. If more than one printer is available, verify that your printer has been selected as the active printer.
Why is the printing garbled on my Oki B4250 Printer?
If the printing from your Oki Printer is garbled, it indicates that the incorrect driver is installed. Install an appropriate driver to resolve this issue.
Explains the purpose of notes for additional information, cautions for equipment damage, and warnings for personal injury.
Describes the operator panel, LEDs, and control button functions for the B4250/B4250n models.
Details the LCD display, buttons, and indicators of the menu-driven operator panel for B4350 models.
Provides instructions and safety precautions for replacing the toner cartridge and cleaning the LED array.
Explains image drum life, replacement procedure, and how to reset the drum counter.
Guides on printing cleaning pages to resolve print quality issues using Status Monitor or control buttons.
Explains how printer status and error messages are displayed and interpreted for different models.
Details procedures for clearing input, feed, and exit paper jams, including safety warnings.
Lists common print quality issues, their causes, and solutions in a symptom-problem-solution format.
Covers troubleshooting for software problems like driver errors and hardware issues like memory or configuration errors.
General| Print Resolution | 1200 x 1200 dpi |
|---|---|
| Monthly Duty Cycle | 50, 000 pages |
| Paper Capacity | 250 sheets |
| Duplex Printing | Yes |
| Connectivity | USB 2.0, Ethernet |
| Maximum Paper Size | Legal |
| Weight | 26.5 lbs (12 kg) |
To Next Page
