What does 'Cannot feed paper set cassette 1' mean on Olivetti d-COPIA 3014MF All in One Printer?
If your Olivetti All in One Printer displays 'Cannot feed paper set cassette 1', one of the paper feeders or the printer cassette upper than the selected one may not be properly closed when one or more optional feeders are installed. Close the paper feeder properly.
Why my Olivetti d-COPIA 3014MF All in One Printer cannot print?
If your Olivetti All in One Printer is not printing, check the following: Ensure the power cord is plugged into an AC outlet, the printer is powered on, and the printer cable is securely connected. If the machine was powered on before connecting the printer cable, power it on again after connecting the cable. Also, check if the print job is paused; if so, press [Resume]. Finally, if an error message is displayed, follow the corresponding procedure.
Why are my Olivetti d-COPIA 3014MF All in One Printer printouts too light?
If the printouts from your Olivetti All in One Printer are too light, verify these possible causes: Ensure that the machine is not in Manual Density mode, and if it is, select the correct density level. Shake the toner container from side to side to distribute the toner evenly. If there is a message indicating the addition of toner, replace the toner container. Replace the paper if it is damp. Disable EcoPrint mode if it is enabled. Also, ensure the paper type setting is correct for the paper being used.
What to do if Olivetti d-COPIA 3014MF ejects blank sheets?
If your Olivetti All in One Printer is ejecting blank sheets, check if the originals are loaded correctly. When placing originals on the platen, place them face-down and align them with the slit glass. When using the document processor, ensure originals are placed face-up.
What to do if Olivetti d-COPIA 3014MF All in One Printer displays 'Error occurred'?
If your Olivetti All in One Printer displays 'Error occurred. Turn the power switch off and on', a system error has occurred. Turn the power switch off and on.
What does 'Unknown toner Installed' mean on Olivetti d-COPIA 3014MF?
If your Olivetti All in One Printer displays 'Unknown toner Installed', the installed toner container's regional specification may not match the machine's. Install the specified container.
How to troubleshoot 'Cannot send via SMB' on Olivetti All in One Printer?
If you cannot send via SMB with your Olivetti All in One Printer, check the following: Ensure the network cable is securely connected. Configure the TCP/IP settings properly. Check sharing settings and access privileges under the folder properties. Set the SMB protocol setting to [On]. Verify the [Host Name], [Path], [Login User Name], and [Login Password] are entered correctly. If the same domain name has been used for both [Host Name] and [Login User Name], delete the domain name and backslash ('\') from the [Login User Name]. Configure exceptions for Windows Firewall properly. Ensure the time settings for the equipment, domain server, and data destination computer are the same. If the panel displays Send error, refer to Responding to Send Error.
What to do if Olivetti d-COPIA 3014MF displays 'Add toner'?
If your Olivetti All in One Printer displays the message 'Add toner' and the attention LED is lit, replace the toner container.
Why do vertical streaks appear on prints from Olivetti d-COPIA 3014MF?
If vertical streaks appear on prints from your Olivetti All in One Printer, the slit glass may be dirty. Clean the slit glass. The inside of the machine may also be dirty; check the toner container and replace it if necessary.
What to do if pressing Start key does not produce copies on Olivetti All in One Printer?
If pressing the Start key on your Olivetti All in One Printer does not produce copies, the machine might be in Sleep mode. Press any key on the operation panel to recover the machine from Sleep mode. The machine will be ready to copy within 15 seconds.
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Print Technology | Laser |
| Print Speed (Black) | 30 ppm |
| Print Resolution | Up to 1200 x 1200 dpi |
| Copy Speed (Black) | 30 cpm |
| Copy Resolution | 600 x 600 dpi |
| Scan Type | Flatbed, ADF |
| Scan Resolution | 600 x 600 dpi |
| Fax Transmission Speed | 33.6 Kbps |
| Max Paper Size | A4 |
| Operating System Compatibility | Windows, Mac OS, Linux |
| Duplex Printing | Yes |
| Automatic Document Feeder Capacity | 50 sheets |
| Display | LCD |
| Type | All-in-One Printer |
| Paper Capacity | 250 sheets |
| Connectivity | USB, Ethernet |
To Next Page