Omron H5CC - Input Circuits; Input Connections

H5CC
1010
Input Circuits
Signal, Reset, and Gate Input
Input Connections
The inputs of the H5CC are no-voltage (short-circuit or open) inputs or voltage inputs. (Reverse connection is not possible because there is polarity.)
(The inputs of the H5CC-A11F/L8@ are no-voltage inputs only. The H5CC-L8E@ does not have an input.)
No-voltage Inputs (NPN Inputs)
Note: When an AC input signal will be input to signal, reset, and gate inputs.
Input the signal via a relay, etc. because AC input cannot be input directly.
Voltage Inputs (PNP Inputs) Note: The inputs of the H5CC-A11F/L8@ are no-voltage inputs only.
Voltage Input Signal Levels
Open Collector Voltage Output Contact Input DC Two-wire Sensor
No-contact Input (NPN Transistor) No-contact Input (PNP Transistor) Contact Input
High level (Input ON): 4.5 to 30 VDC
* The DC voltage must be 30 VDC max.
* Input resistance: Approx. 4.7 kΩ
Low level (Input OFF): 0 to 2 VDC
Internal
circuit
IN
+14
V
Approx.
1 k:
Internal
circuit
IN
Approx. 4.7 k:
No-voltage Inputs (NPN Inputs)
Other than the H5CC-A11F
Voltage Inputs (PNP Inputs)
H5CC-A11F
+5 V
Approx.
20 k:
Approx. 1.2 k:
Internal
circuit
IN
H5CC-A@
H5CC-AWSD
--
-
-
H5CC-A11@
H5CC-L8@
PLC or
sensor
0 V for inputs
Reset input Reset input
Signal input
Gate input
Note: Operate with transistor ON
6789
678910
3765
134
H5CC-A@
H5CC-AWSD
H5CC-A11@
H5CC-L8@
0 V for inputs
Reset input Reset input
Signal input
Gate input
Note: Operate with transistor ON
Sensor
--
-
-
6789
3765
134
678910
H5CC-A@
H5CC-AWSD
H5CC-A11@
H5CC-L8@
0 V for inputs
Reset input Reset input
Signal input
Gate input
--
-
-
9
910
5
678
376
134
678
Note: Operate with relay ON
0 V for inputs
Reset input Reset input
Signal input
Gate input
Note: Operate with transistor ON
H5CC-A@
H5CC-AWSD
H5CC-A11@
H5CC-L8@
--
-
-
9
910
5
678
376
134
678
Applicable Two-wire Sensor
• Leakage current: 1.5 mA max.
• Switching capacity: 5 mA min.
• Residual voltage: 3.0 VDC max.
(1.0 VDC max. for the
H5CC-A11F)
• Operating voltage: 10 VDC
No-voltage Input Signal Levels
* The DC voltage must be 30 VDC max.
No-contact
input
Short-circuit level (Transistor ON)
• Residual voltage: 3.0 VDC max. (1.0 VDC max. for the H5CC-A11F)
• Impedance when ON: 1 kΩ max. (The leakage current is approx. 12 mA when the
impedance is 0 Ω.) (
Approx. 1
mA
for the H5CC-A11F)
Open level (transistor OFF)
• OFF impedance: 100 kΩ min.
Contact input Use contacts which can adequately switch 5 mA at 10 V.
Relay
H5CC
0 V for inputs
Reset input
Signal input
Gate input
6789
(Example)
Connection example
0 V for inputs
Reset input Reset input
Signal input
Gate input
H5CC-A@
H5CC-AWSD
H5CC-A11@
Sensor
Note: Operate with transistor OFF
-
-
9
5
910
678
376
678
0 V for inputs
Reset input Reset input
Signal input
Gate input
Sensor
H5CC-A@
H5CC-AWSD
H5CC-A11@
Note: Operate with transistor ON
-
-
9
5
910
678
376
678
0 V for inputs
Reset input Reset input
Signal input
Gate input
Note: Operate with relay ON
H5CC-A@
H5CC-AWSD
H5CC-A11@
-
-
9
910
5
678
376
678