Omron H5CC - Page 16

H5CC
1616
Operating Procedures of the H5CC-A@/L@
Setting Procedure Guide
Settings for Timer Operation *
Use the following settings.
Settings for Twin Timer Operation *
Refer to page 26.
* “Timer” is set in the default settings. Refer to page 33 fo
r information on switching models.
*2
*1
Function
setting mode
* Use UP1+UP3 to move up and
DW1+DW3 to move down
shs
(1 ms)(20 ms)
( A-1) ( A-2) ( A-3) ( b-1) ( b-5) ( b) ( C) ( d) ( E) ( F) ( G) ( H) ( S) ( Z)
Output time
Note: Displayed only when the model is not H5CC-L8E@ or H5CC-A11F.
Note: Displayed only when the model is H5CC-A@ or H5CC-A11@. (However, not displayed for H5CC-A11F.)
Step1
The characters displayed in reverse video are the default settings. In the function setting mode, the status indicators of the keys that
can be set light up.
(Example) In the case of the
Output time
A value from 0.01 to 99.99 s can be set, and therefore the status indicators of the UP1 to UP4 Keys (DW1 to DW4 Keys) light up.
*
*
*
*
*
*
Change to Function Setting Mode.
To
next page
From
next page
Output time
(0.01 s) (99.99 s)(Output hold)
Note: Displayed for modes A, A-1, A-2, A-3, b, b-1 and S only.
(0.01 s) (99.99 s)(Output hold)
Time range
Timer mode
(DOWN)(UP)
(A)
Note: Only A-2, b, E, and Z can be selected for the H5CC-L8E@.
Output
modes
Input signal
NPN/PNP
input
(PNP input)(NPN input)
Function Setting Mode
……
s
20ms 1ms
down
-----.-
------
---.---
up
za-1a a-2
99.990.01hold
99.990.01hold
hold
a-3 b
cb-1 b-5 d e f gh s
----.--
pnpnpn
----.--
s
-----.-
s
------
s
--:--:--
hm s
s
----:--
hm
-----.-
h
------
h
---.---
-----.-
m
------
m
• Set the output mode using the UP1 Key (DW1 Key).
• Set each digit using the individual UP1 to UP4 Keys (DW1 to DW4 Keys).
0.01 s to 9999.99 s
(default setting)
0.1 s to 99999.9 s
1 s to 999999 s
0 h 0 min 01 s to 99 h 59 min 59 s
0 h 01 min to 9999 h 59 min
0.1 h to 99999.9 h
1 h to 999999 h
0.001 s to 999.999 s
0.1 min to 99999.9 min
1 min to 999999 min
Display Set Value
Time Range List
(If the output time is set to 0.00, is displayed.)
• Set the time range using the UP1 Key (DW1 Key).
For details, refer to the Time Range List.
• Set the timer mode using the UP1 Key (DW1 Key).
• Set the input signal width using the UP1 Key (DW1 Key).
• Set the NPN/PNP input mode using the UP1 Key (DW1 Key).
*1. If the mode is switched to the function setting mode during operation, operation will continue.
*2. Changes made to settings in function setting mode are enabled for the first time when the
mode is changed to run mode. Also, when settings are changed, the timer is reset (time
initialized and output turned OFF).
UP1+UP3 or DW1+DW3
(Press and hold for 2 s)
UP1+UP3 or DW1+DW3
(Press and hold for 2 s)
Run mode
Power ON
a
outm
20m5
iflt
npn
imod
up
timm
hold
otim
hold
otim
----.--
timr
For details on operations in run mode, refer to page 19.