Omron SYSMAC CP2E-N D Series User Manual

Index-3
CP2E CPU Unit Software User’s Manual(W614)
K
keep-alive field ...........................................................15-21
L
Ladder program
Editing ..................................................................18-16
Input .......................................................................18-7
Saving and reading ..............................................18-14
Transferring ..........................................................18-18
Writing ....................................................................18-7
Less Than Flag(P_LT)..................................................5-26
Less than or Equals Flag(P_LE)..................................5-26
Linear mode(high-speed counter)..............................11-10
Local symbols ................................................................4-6
M
main response code...................................................15-23
Maximum interrupt task processing time(A440CH) ...10-13
Memory areas and stored data......................................2-3
Modbus-RTU Easy Master...........................................14-5
DM fixed allocation words ...........................5-12, 14-15
Error codes...........................................................14-16
Programming examples .......................................14-18
Related Auxiliary Area..........................................14-16
mode settings
reading from Unit..................................................15-25
Monitor mode................................................................. 3-3
Monitoring and debugging .........................................18-23
Forced set/reset ...................................................18-25
Monitoring status..................................................18-23
Online editing ....................................................... 18-26
MRES.........................................................................15-23
MSKS instruction ..............................................10-6, 10-11
N
Negative Flag(P_N) .....................................................5-26
No. field ......................................................................15-21
Non-differentiated instructions .....................................4-16
No-protocol communications ............................14-5, 14-10
PLC Setup............................................................14-11
Related Auxiliary Area..........................................14-12
Not Equal Flag(P_NE) .................................................5-26
Number of connected Units ...........................................6-3
O
Online editing....................................................17-9, 18-26
Opening Flag .............................................................15-40
Operands .....................................................................4-15
Operating mode at startup .............................................7-3
Operating modes
Changing method.....................................................3-3
Operating modes and operation...............................3-4
The retaining of I/O memory when changing ...........3-4
Operation for power interruptions.............................. A-104
Timing Chart........................................................ A-105
ORG instruction .................................. 12-14, 12-34, 12-42
Origin return settings ....................... 7-19, 7-21, 7-22, 7-24
Origin search settings ...................... 7-18, 7-20, 7-21, 7-23
OUT instruction...............................................12-14, 12-34
Output interrupts ..........................................................10-2
Overflow Flag(P_OF) ...................................................5-26
P
P_AER(Access Error Flag) ..........................................5-25
P_CY(Carry Flag) ........................................................5-25
P_EQ(Equals Flag) ......................................................5-25
P_ER(Error Flag) .........................................................5-25
P_GE(Greater Than or Equals Flag) ...........................5-26
P_GT(Greater Than Flag)............................................5-25
P_LE(Less than or Equals Flag) ..................................5-26
P_LT(Less Than Flag)..................................................5-26
P_N(Negative Flag)......................................................5-26
P_NE(Not Equal Flag) .................................................5-26
P_OF(Overflow Flag) ...................................................5-26
P_Off(Always OFF Flag) ..............................................5-25
P_On(Always ON Flag)................................................5-25
P_UF(Underflow Flag) .................................................5-26
Peripheral servicing .......................................................3-2
Phase-Z signal + software reset ................................11-11
PID temperature control...............................................16-2
PIDAT instruction..........................................................16-3
PING ..........................................................................15-15
echo test...............................................................15-15
PLC Setup......................................................................7-2
Base Settings ............................. 7-18, 7-19, 7-21, 7-22
Communications settings ........................ 7-5, 7-9, 7-13
Execute process settings .........................................7-3
High-speed counter settings...................................7-16
Input constant...........................................................7-4
Interrupt input settings............................................7-17
Origin return settings.....................................7-21, 7-24
Origin search settings7-18, 7-19, 7-20, 7-21, 7-22, 7-23
Settings ....................................................................7-3
Startup data read setting..........................................7-3
Startup mode setting ................................................7-3
Timing and interrupt settings....................................7-4
PLS2 instruction..............................................12-14, 12-16
Port No. field ...................................................15-56, 15-57
port numbers
UDP port
reading from Unit .........................................15-25
Positioning control......................................................12-16
Positioning control (independent mode).....................12-66
Precautions
Ladder programming precautions ..........................4-35
Precautions for using interrupts............................10-13
Special program sections .......................................4-35
Program capacity ...........................................................4-3
Program mode ...............................................................3-3
Program-free communications with PTs ......................14-7
PLC Setup and PT system settings........................14-8
Programmer device......................................................18-3
Programming .................................................................4-2
PRV instruction ................................... 11-12, 12-14, 12-44
Pulse + Direction input.................................................11-9
Pulse input
methods
....................................................11-8
Pulse output change response time.......................... A-103
Pulse output Start Time ............................................ A-103
Pulse outputs ...............................................................12-3
Application example .............................................12-46
Changing the present value of the pulse output... 12-43
Defining origin position.........................................12-30
Functions allocation.......................................12-4, 12-6
Jogging.................................................................12-20
Output pattern ......................................................12-64
PLC Setup ..............................................................12-5
Positioning control ................................................12-16
Positioning control (independent mode) ...............12-66
Precautions when using pulse outputs.................12-59

Omron SYSMAC CP2E-N D Series Specifications

General

Brand	Omron
Model	SYSMAC CP2E-N D Series
Category	Computer Hardware
Language	English