19
→
FM MODE
STANDBY/ON
STANDBY
POWER
PHONES
OFF
ON
TUNING/PRESET
SURROUND STEREO
T – D
DISPLAY
DVD / CD
PRESET
MEMORY
SUBWOOFER
MODE
SPEAKER
SETUP
SPEAKER
A / B
ACOUSTIC
CONTROL
INPUT
MASTER VOLUME
Setting up Non-Optional Speakers
SPEAKER
SETUP
Display SPEAKER
SETUP
I
N
P
U
T
S
E
L
E
C
T
O
R
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
L
I
S
T
E
N
I
N
G
M
O
D
E
A
.
C
T
R
L
T
–
D
S
T
E
R
E
O
S
U
R
R
T
I
T
L
E
M
E
N
U
S
E
T
U
P
T
V
/
V
C
R
R
E
T
U
R
N
CH
TUN
VOLENTER
REPEAT MUTING
A – B
REC
DIMMER
OPEN/CLOSE
RANDOM SLOW
SUBTITLE – ON / OFF
ANGLE ZOOM
MEMORY CLEAR AUDIO DISPLAY
--
/
---
SW MODE
LATE NIGHT DISTANCE
CH SEL
T– D SETUP
UP/ DOWN
TEST TONE
SP A
SP B
123
456
789
+
10 0
SEARCH
S
T
N
B
Y
O
N
S
L
E
E
P
A
U
D
I
O
Unit
Remote controller
SUBWOOFER
MODE
SW MODE
1
Before operating the
remote controller
Press MODE AUDIO.
The remote controller
remains in the AUDIO mode,
until another MODE button is
pressed.
→
Setting the Subwoofer Mode
Press SUBWOOFER MODE on the
unit or SW MODE on the remote
controller.
With the first press of the button, you can
check the present setting. Then each press
of the button changes the subwoofer mode
as follows (a tip on how to select the right
subwoofer mode is in parentheses):
SW Mode 2*
(When large–wideband–front speakers
are connected)
↓
SW Off
(When no subwoofer is connected)
↓
SW Mode 1
(When small–with limited bass signal
handling–front speakers are
connected)
The normal display resumes in three
seconds.
SUBWOOFER
MODE
SW MODE
→
Unit only
* (For USA and Canadian models)
The display appears in the following order:
SW Mode 1
↓
SW Mode 2
↓
SW Off
Selecting the number of speaker channels
Press SPEAKER SETUP repeatedly
to select the number of channels
for the SPEAKERS A system.
(USA and Canadian models)
Alghough “SmartConfig” may appear in the
display, do not select “SmartConfig” in this
step.
Pressing the button repeatedly within three
seconds changes the number of channels
as follows (the corresponding speaker
configuration is described in parentheses):
SmartConfig
Appears if your DVD Receiver is the USA or
Canadian model. Do not select this in this step.
↓
Speaker 2
ch
(Front left and right speakers)
↓
Speaker 3
ch
(Front left, center, and right speakers)
↓
Speaker 4
ch
(Front left and right, plus surround left
and right speakers)
↓
Speaker 5
ch
(Front left, center, and right, plus
surround left and right speakers)
The normal display resumes in three
seconds.
Notes
• The listening mode will automatically be set to
“Stereo” (see page 38) once you set or reset
the number of channels.
• To check the present setting while the normal
display is displayed, press SPEAKER SETUP
once. To change the setting, press the button
repeatedly within three seconds.
To Next Page
Loading...
Need help?
General
