To Next PageTo Next PageWhat to do if Onkyo Receiver shows error during the update process?
If your Onkyo receiver displays an error during the update, disconnect and then reconnect the AC power cord. After that, try the update process again.
What does error code *-11, *-13, *-21, *-28 mean on my Onkyo Receiver?
These error codes indicate an Internet connection error. Check the following: * Make sure the IP address, subnet mask, gateway address, and DNS server are configured properly. * Ensure the router is turned on. * Verify the AV receiver and the router are connected with an Ethernet cable. * Confirm your router is configured correctly. If your network allows only one client connection and another device is already connected, the Onkyo receiver will not be able to access the network. If you are still unable to access the Internet, the DNS or proxy server may be temporarily down.
What does error code *-10, *-20 mean on my Onkyo Receiver?
The error codes *-10 or *-20 indicate that the Ethernet cable was not detected. Reconnect the cable properly to resolve this issue.
What to do if Onkyo Receiver displays Error!! *-** on the front display?
Retry the update procedure from the beginning. If the error persists, no answer.
General| Receiver type | Surround |
|---|---|
| Input sensitivity | 200 mV |
| Audio output channels | 9.2 channels |
| Signal-to-Noise Ratio (SNR) | 110 dB |
| Total Harmonic Distortion (THD) | 0.05 % |
| Power output per channel (20-20KHz@8 Ohm) | - W |
| HDMI in | 8 |
| AC (power) in | Yes |
| Composite video in | 5 |
| USB ports quantity | 2 |
| S-Video inputs quantity | 4 |
| Multichannel audio input type | RCA |
| Component video (YPbPr/YCbCr) in | 3 |
| Component video (YPbPr/YCbCr) out | 1 |
| Connectivity technology | Wired |
| Ethernet LAN | No |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Preset stations quantity | 40 |
| Display | - |
| Product color | Black |
| Audio decoders | Dolby TrueHD, DTS-HD Master Audio |
| Apple docking compatibility | iPhone, iPod |
| AC input voltage | 220-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 110 W |
Weight and Dimensions| Depth | 453.5 mm |
|---|---|
| Width | 435 mm |
| Height | 198.5 mm |
| Weight | 14000 g |
Critical safety warnings and precautions to prevent fire, electric shock, and injury. Read before use.
Operational precautions regarding copyright, AC power, care, hearing loss, batteries, and handling.
Connect AV controller PRE OUT jacks to amplifier inputs and speakers to amplifier terminals.
Connect AV controller PRE OUT jacks to amplifier via balanced XLR audio cables.
Specifies which speakers to use based on setup and sets crossover frequency.
Connects powered subwoofers to SW1/SW2 PRE OUT or Subwoofer PRE OUT jacks.
Improves bass and treble performance by using separate amplifier channels for speakers.
Instructions for powering the AV controller on, off, and into standby mode.
Connect and play music/video files from an iPod/iPhone using the USB port.
Connect and play music files from a USB device like flash drives or MP3 players.
Automated setup using a microphone to optimize speaker performance.
Manually adjust speaker settings after automatic setup or for custom configurations.
Accesses on-screen setup menus for configuring AV controller settings.
Specifies connected speakers and sets crossover frequencies for each.
Enables Audyssey audio processing for room correction and speaker setup.
Optimizes sound quality for varying volume levels using Audyssey.
Manages volume level variations between programs and movies.
Configures network settings (DHCP, IP Address, DNS) for internet connectivity.
Troubleshooting steps for issues related to powering the AV controller on or off.
Solutions for no sound, quiet sound, or incorrect audio output issues.
Troubleshooting steps when remote control of other components fails.
Instructions for updating the AV controller's firmware via network or USB.
Steps to update firmware using a wired Internet connection.
Steps to update firmware using a USB storage device.
Enables system control over HDMI for RIHD-compatible devices.
Details linked operations enabled by connecting RIHD-compatible devices.
Step-by-step guide for connecting and setting up HDMI Control (RIHD).
Technical details and features of the AV controller's amplifier, tuner, and general components.
