Onkyo TX-8270 - Page 73

EN FR ES IT DE NL SV 繁中
З
JP
5. Usethe or buttonsontheremotecontrollertodisplay“ConnectDevice”
andpressENTER.ThiswillallowyoutoseealltheSonosdevicesonthe
samenetworkastheunit.SelecttheSonosConnectthatisconnectedtoyour
unitandpressENTER.
(Note)
• ProductsotherthanSonosConnect(productswithoutoutputterminalssuch
asPlay:3)arealsodisplayedinthelistandareselectable.Inthesecases,
inputswitcheswhenplaystartsontheSonosproduct,buttheaudioisnot
output.SelecttheroomnamefortheconnectedSonosConnect.
• ThelistofSonosproductscanshowupto32units.Ifyoucannotndthe
SonosConnectyouwanttolinkwith,returntothepreviousscreen,turnoff
theproductsyoudonotwanttolink,thentryagain.
6. Usethe or buttonsontheremotecontrollertodisplay“OutZone:”and
thenusethe or buttonstoselecttheZonewhereyouwanttohearthe
music.Theunitautomaticallyswitchestoplayinthemainroom(theroom
wherethisunitis),anotherroom(Zone2)orM/Z2(themainroomandZone
2),accordingtoplayonSonosConnect.SomeunitsmayhaveadditionalZone
outputs.
7. Pressthe (SETUP)buttonontheremotecontrollertoexitthesetupmenu.
8. Setupisnowcompleteandyouarereadytouseyourequipment.
• Thepoweronlinkingdependsonthenetworkstandbyfunctionofthisunit.
Fordetails,refertothisunit'sinstructionmanual.
Now the fun part - listening to Sonos on
your Unit
1. UsingyourSonosAppselectthemusicyouwanttolistentoandsendittothe
room(orgroup)whereyourunitislocated.Werecommendnamingyourunit
/SonosConnectcombinationafriendlynamelikeTVRoomorLivingRoom
wheretheequipmentislocated.
2. JustlikeyourotherSonosspeakersandgearthatyouarefamiliarwithyou
cangroupyourunitwithotherspeakersorlistentoitbyitself.
(Note)
Iftheinputonyourunitdoesnotchangeautomaticallywhenplaystarts,try
stoppingplay,thenstartingitagain.
Setting the Preset Volume
YoucansetthevolumethatSonosConnectwillbeplayedatbeforehand.The
volumesetwillbeusedonlywhenusingSonosConnect.
1. Press

(SETUP)buttonontheremotecontrollertodisplaythesetupmenu.
2. Pressthe
or buttonsontheremotecontrollertodisplay"WorksSONOS".
• If"WorksSONOS"isnotdisplayed,select"Hardware"andpressENTER,
thenpressthe or buttonsontheremotecontrollertodisplay
"WorksSONOS".
3. Select"WorksSONOS",andpressENTER.
4. Pressthe or buttonsontheremotecontrollertoselect"PresetVolume"
andpressENTER.
5. Pressthe or buttonsontheremotecontrollertodisplaythemainroom
(wherethisunitislocated)oranotherroom(Zone2orZone3,forexample),
thenpress or tosetthevolume.
• Select"Last"toreturntotheinitialsetting.
6. Press

(SETUP)buttonontheremotecontrollertoexitthesetupmenu.
SN29403425B_SONOS CONNECT_En_onk_181010.indd 2 2018/10/05 9:37:49