To Next Page
M
Mrs. Jocelyn Phelps DDSAug 19, 2025
How to fix no power on my Onkyo TX-SR600 Receiver?
- JJustin GraySep 12, 2025
If your Onkyo Receiver has no power, the power cord may be disconnected. Ensure the power cord is securely connected.
How to fix no power on my Onkyo TX-SR600 Receiver?
If your Onkyo Receiver has no power, the power cord may be disconnected. Ensure the power cord is securely connected.
Why is my Onkyo TX-SR600 remote not working?
If the front panel controls on your Onkyo Receiver work, but the remote controller does not, consider the following: * Ensure there are batteries in the remote. * Replace the batteries if they have worn out. * Point the remote controller at the remote sensor of the receiver. * Operate the remote controller within 16 feet (5 meters). * Press the RCVR MODE button, as the remote may be functioning in a different mode.
How to fix no sound from the center speaker on my Onkyo TX-SR600?
If you are experiencing no sound or very low volume from the center speaker of your Onkyo Receiver, consider the following: * Check the speaker cable connection between the amplifier and speaker. * Ensure the listening mode is set to a mode other than Stereo or Direct. * Verify the center speaker volume is appropriately set. * Confirm that the Center setting is set to “Large” or “Small” at “Speaker Config” and not to “None.”
Why does my Onkyo TX-SR600 Receiver shut off immediately after turning it on?
If your Onkyo Receiver shuts off immediately after being powered on, the amplifier protection circuitry may be activated. Remove the power cord from the outlet immediately and contact your Onkyo service center.
What to do if no picture appears on the TV screen from my Onkyo TX-SR600?
If no picture appears on the TV screen (or monitor) when using your Onkyo Receiver, ensure that the TV (or monitor) is set to receive the input from the receiver. Also, check that the video cable is securely connected. If the input source is connected to the COMPONENT VIDEO IN connectors, ensure the TV (or monitor) is connected to COMPONENT VIDEO OUT connectors.
Why does my Onkyo Receiver sound scratchy?
If you hear a rough or scratchy sound and the high range is not clear on your Onkyo Receiver, it could be due to several reasons: * An internal fuse may be blown – in this case, contact your Onkyo Service Center. * If using a turntable (TX-SR700/700E only), the needle may be dirty or worn, or there could be a problem with a connected component – refer to the instruction of the connected components and check for problem. * The treble control may be set too high – turn the treble setting down at Audio Adjust ? Treble.
Why is the subwoofer volume so low on my Onkyo TX-SR600 Receiver?
If you experience no sound or very low volume from the subwoofer connected to your Onkyo Receiver, verify that the Subwoofer setting is set to “Yes” at “Speaker Config”. Also, check that the subwoofer level is set to an appropriate volume.
Why is there no OSD menu display on my Onkyo TX-SR600 Receiver?
If there is no OSD Menu display on your Onkyo Receiver, it could be due to an improper connection. Check the connections. The OSD Menu is displayed when the monitor is connected to VIDEO or S VIDEO of MONITOR OUT, so check these connections as well.
What causes crackling noise on AM and FM stations on my Onkyo TX-SR600?
If you're experiencing crackling noise on both AM and FM stations with your Onkyo Receiver, it could be due to noise caused by a fluorescent lamp being turned on and off, so move the antenna as far as possible from the lamp. It also may be noise from automobile ignition, in that case install an FM outdoor antenna as far as possible from the road and change the position or direction of the outdoor antenna.
Why is there a buzzing noise on AM stations with my Onkyo TX-SR600?
If you are experiencing a buzzing noise on AM stations, particularly at night or with weak stations, it may be due to noise from electrical apparatus such as a fluorescent lamp. Try moving the AM loop antenna to a different position. You might also consider setting up an outdoor AM antenna.
Details about power output, distortion, technology, audio formats, and video connectivity.
Instructions for voltage selection and remote controller setup before first use.
Overview of the TX-SR700E/600E front panel controls and displays.
Guide on how to properly connect speakers for optimal surround sound.
Setting up speaker parameters like subwoofer, size, and crossover frequency.
Setting digital input, format, multichannel, component video, and IntelliVolume.
Step-by-step guide to entering 3-digit codes for component control.
Step-by-step process for learning commands from another remote.
Recording and triggering button operation sequences as macros.
General
