User’s ManualUser’s Manual
Optex Inc. - 1845 W 205th St. - Torrance, Ca. 90501 - 800-966-7839 SMDC-16 User’s Manual 3440-0250 A3
6 of 16
Arming / Disarming (With Groups)
General Description
• Your security system allows for three individual
arming modes, AWAY, STAY and INSTANT.
• Your alarm company will explain in detail to you how
each of your protection devices will react in each of
the three different arming modes.
• Your alarm company has programmed a value of time
to allow you to arm your system and vacate the
premises without generating an alarm condition.
Away Group Arming
Arming Description ::
• Away Group Arming should be used when all
personnel will be leaving the premises and all
protection devices(s) will be active.
• The entry delay will remain available to any personnel
that requires re-entry to the premises with the security
system armed in this mode.
• There are two methods of Away Group Arming:
Method 1:
1. Press AWAY.
2. Enter your PIN.
3. The keypad will be scrolling the groups available for you
to arm.
4. Select the group number(s) on the keypad.
5. Press AWAY.
6. Observe display “AWAY Exit Delay” “Exit in xx Secs”.
7. Exit premises
Example:
press AWAY + Œ•Ž• +G### + AWAY - exit (G ###
represent group numbers).
Method 2:
1. Press AWAY.
2. Enter your PIN.
3. The keypad will be scrolling the groups available for
you to arm.
4. Press AWAY to arm all groups.
5. Observe display “AWAY Exit Delay” “Exit in xx Secs”.
6. Exit premises
Example:
press AWAY + Œ•Ž• + AWAY - exit premises.
Stay Group Arming
Arming Description:
• Stay Group Arming should be used when personnel
will be remaining on the premises and will require
access from area to area without activating an alarm
condition.
• The entry delay will remain available to any personnel
that requires re-entry to the premises with the security
system armed.
• There are two methods of Stay Group Arming:
Arming / Disarming (With Groups)
Stay Group Arming
Method 1:
1. Press STAY.
2. Enter your PIN.
3. The keypad will be scrolling the groups available for
you to arm.
4. Select the group numbers on the keypad.
5. Press STAY.
6. Observe display “Stay Exit Delay” “Exit in xx Secs”.
7. Exit premises (if need be).
Example:
press STAY + Œ•Ž• +G### + STAY (G ###
represent group numbers)
Method 2:
1. Press STAY.
2. Enter your PIN.
3. The keypad will be scrolling the groups available for
you to arm.
4. Press STAY to arm all groups.
5. Observe display “STAY Exit Delay” “Exit in xx Secs”.
6. Exit premises (if need be).
Example:
press STAY + Œ•Ž• + STAY - exit premises (if need
be).
Instant Group Arming
Description:Description:
• Instant arming should be used when personnel will
be remaining on the premises and will require access
from protected area to protected area without
activating an alarm condition.
• Certain zones may be inactive when the alarm system
has been armed in this mode. Contact your alarm
company for further information.
• The entrance delay will not remain available to any
personnel that will require re-entry to the premises
during the armed period.
• There are two methods of Stay Group Arming:
Method 1:
1. Press INSTANT.
2. Enter your PIN.
3. The keypad will be scrolling the groups available for
you to arm.
4. Select the group numbers on the keypad.
5. Press INSTANT.
6. Observe display “Instant Arming” “Exit in xx Secs”.
7. Exit premises (if need be).
Example:
press INSTANT + Œ•Ž• +G### + INSTANT.
(G ### represent group numbers).