Optoma GT2000HDR User Manual

English
21
USING THE PROJECTOR
Powering on / o󰀨 the projector
or
Powering on
1. Securely connect the power lead and signal/source cable. When connected, the Power LED will turn
red.
2. Turn on the projector by pressing the button on the projector keypad or the button on the remote
control.
3. A start up screen will display in approximately 10 seconds and the Power LED will be ashing green or
blue.
Note: The rst time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering o󰀨
1. Turn o󰀨 the projector by pressing the button on the projector keypad or the button on the remote
control.
2. The following message will be displayed:
Power O󰀨
Press power key again.
3. Press the / button again to conrm, otherwise the message will disappear after 15 seconds.
When you press the / button for the second time, the projector will shut down.
4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the Power
LED will ash green or blue. When the Power LED turns solid red, this indicates the projector has
entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle
has nished and the projector has entered standby mode. When the projector is in standby mode,
simply press the / button again to turn on the projector.
5. Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power o procedure.

Optoma GT2000HDR Specifications

General

Number of colors	1.073 billion colors
Native aspect ratio	16:9
Projection distance	0.3 - 3.3 m
Vertical scan range	24 - 120 Hz
Horizontal scan range	15 - 140 kHz
Projection technology	DLP
Supported aspect ratios	4:3, 16:10, 16:9
Contrast ratio (typical)	300000:1
Digital gamma correction	Yes
Screen size compatibility	30 - 300 \
Projector native resolution	1080p (1920x1080)
Keystone correction, horizontal	-30 - 30 °
Light source type	Laser
Service life of light source	30000 h
Focus	-
Offset	116 %
Throw ratio	0.496:1
Focal length range	7.51 mm
Supported video modes	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Analog signal format system	NTSC J, NTSC M, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, SECAM B, SECAM D, SECAM G, SECAM K, SECAM K1, SECAM L
Supported graphics resolutions	640 x 480 (VGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1280 x 800 (WXGA), 1360 x 768 (WXGA), 1920 x 1080 (HD 1080)
HDMI connector type	Full-size
Serial interface type	RS-232
USB 2.0 ports quantity	1
VGA (D-Sub) ports quantity	0
Noise level	32 dB
Number of OSD languages	25
On Screen Display (OSD) languages	ARA, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, FAS, FIN, FRE, GRE, HUN, IND, ITA, JPN, NOR, POL, POR, RUM, RUS, SWE, TUR, VIE
High Dynamic Range (HDR) technology	High Dynamic Range 10 (HDR10), Hybrid Log-Gamma (HLG)
RMS rated power	15 W
Placement	Ceiling, Desktop, Wall
Product type	Short throw projector
Product color	White
Market positioning	Home cinema
Cable lock slot type	Kensington
Power source	AC
AC input voltage	100-240 V
AC input frequency	50-60 Hz
Power consumption (max)	139 W
Power consumption (standby)	0.5 W
Power consumption (typical)	98 W
Operating altitude	0 - 2500 m
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 80 %

Weight and Dimensions

Depth	216 mm
Width	274 mm
Height	114 mm
Weight	3000 g
Package weight	4200 g