Oriental motor BLVM620K-GFS - Connecting Method

7
Connection

Connection example (Sink logic)
FWD
1
CN4
CN2
CN3
CN8
3.3 kΩ
2
+
CN1
-
+
-
3
4
9
10
5
13
12
11
6
CN4
5
14
7
15
8
2
1
3
REV
STOP-MODE
M0
ALARM-RESET
MB-FREE
IN-COM
IN-COM
SPEED-OUT
∗2
∗1
∗2
WNG (+)
WNG (
- )
ALARM-OUT1 (+)
ALARM-OUT1 (
-
)
VH
+15 V
0 V
0 V
0 V
VM
VL
VM
VL
Motor power connector
Driver
Motor signal connector
Electromagnetic brake connector
BLV620:
30 VDC or less
10 mA or less
BLV640:
53 VDC or less
10 mA or less
BLV620:
30 VDC or less
100 mA or less
BLV640:
53 VDC or less
100 mA or less
BLV620: 24 VDC±10%
BLV640: 48 VDC±10%
DC power supply
External DC voltage
(Not to exceed the
voltage selected by
SW1-No.2)
External potentiometer
PAVR-20KZ (accessory)
*1 Be sure to suppress the current value to 10 mA or less. Connect a current-limiting resistor if the current exceeds this specied value.
*2 Be sure to suppress the current value to 100 mA or less. Connect a current-limiting resistor if the current exceeds this specied value.

Connecting the power supply
z
Connecting method
1. Strip the insulation cover of the lead wire by
10 mm (0.39 in.).
Applicable lead wire: AWG16 to 10
(1.25 to 6 mm
2
)
10 mm
(0.39 in.)
2. Insert each lead wire into the CN1 connector
and tighten the screw.
Tightening torque: 0.7 to 0.8 N·m
(6.1 to 7.0 lb-in)
CN1
connector
Lead wire
3. Insert the CN1 connector into CN1.
Hold the green part of the CN1 connector, and insert it into the CN1 on the
driver. Push the lever (orange) into the CN1 on the driver before pulling
out the CN1 connector.
Lever
Supplying the power in a state
where the lever (orange) is pushed
in may cause damage to the driver
due to connection failure.
Note

When connecting, check the indication of the driver case and
pay attention to the polarity of the power supply. Reverse-
polarity connection may cause damage to the driver.

Do not wire the power supply cable of the driver in the
same cable duct with other power line or motor cable.
Doing so may cause malfunction due to noise.

When cycling the power or plugging/unplugging the connector,
turn o󰀨 the power and wait for the POWER LED to turn o󰀨.

When turning on or o󰀨 the power supply using a
mechanical contact (breaker, electromagnetic switch, relay,
etc.), do so only the positive side (+) of the power supply
using the mechanical contact. Turning on or o󰀨 the positive
side (+) and the negative side (-) of the power supply
simultaneously using a mechanical contact may cause
damage to the control circuit or peripheral equipment.
z
Applicable crimp terminal
If crimp terminals are used, select the following terminals.
Manufacturer Model Applicable lead wire
PHOENIX CONTACT
GmbH & Co. KG
AI 1,5-10 AWG16 (1.25 mm
2
)
AI 2,5-10 AWG14 (2 mm
2
)
AI 4-10 AWG12 (3.5 mm
2
)
z
Recommended power supply capacity
Unit model Input power supply voltage Current capacity
BLV620
24 VDC±10% 800 W or more
BLV640
48 VDC±10% 1 kW or more

Connecting the motor and driver
Connect the motor cable to the motor power connector (CN2) and motor
signal connector (CN3) of the driver. When using a electromagnetic brake
motor, also connect to the electromagnetic brake connector (CN8).
To expand connection between the motor and driver, use the included
connection cable. Connection can be extended to a maximum of 3.5 m
(11.5 ft.).
Note
Have the connector plugged in securely. Insecure connection
may cause malfunction or damage to the motor or driver.

Connecting the I/O signals
Connecting the I/O signals to the I/O connector (CN4). Keep the wiring
distance as short as possible [less than 2 m (6.6 ft.)] to suppress the eect of
noise.
Note

The connector for connecting the I/O signals are not
included. Please prepare as follows;
· D-Sub connector (15-pin)
· Hood (the screw: No.4-40UNC)

Wire the signal cable at a distance of 100 mm (3.94 in.) or
more from the inductive load (electromagnetic relay etc.),
power supply or power cable (motor cable etc.).