How to start the pump dehumidification cycle (H2OUT) on Orved Evox 31 Hi-Line Kitchen Appliances?
If the display flashes 'RUN H2OUT PRESS START', it means the pump has absorbed moisture. Start the Pump dehumidification cycle (H2OUT) by pressing “START”.
What to do if my Orved Evox 31 Hi-Line Kitchen Appliances sealing is not optimal?
If the sealing isn't optimal, it could be due to several reasons: * The sealing level might not be correct for the bag type. Try adjusting it and repeating the cycle. * Too many consecutive sealing cycles might have been performed, causing overheating. Wait at least 2 minutes between cycles. * The bag might be too large. Use a suitable bag. * The bag edge might not be positioned correctly, or it might be dirty. Position it centrally, protruding about 2 cm, and ensure it's clean. Turn the edge of the bag over so that the outer part remains clean when the product is inserted. Make sure the edge doesn’t form creases near the sealing bar. * The sealing bar and counter-pressure rubber could be dirty or damaged. Clean them. If damaged, contact the Technical Support Service.
What to do if Orved Kitchen Appliances displays 'VACUUM NOT STARTED' during a cycle?
If the display shows 'VACUUM NOT STARTED' accompanied by an audible signal during a cycle, it indicates that the vacuum isn't activated. This could be because: * The lid hasn't been closed properly. Gently press on the lid to activate the vacuum when the cycle starts. * There is dirt on the lid seal. Clean the vacuum chamber and seal. * The lid seal is broken. Contact the Technical Support Service for replacement. * The pump protection has been activated. Leave the packaging machine to cool. If the fault recurs contact the Technical Support Service.
What to do if my Orved Evox 31 Hi-Line Kitchen Appliances sealing bar is raised but sealing does not occur?
If the sealing bar is raised but sealing isn't happening, it could be because: * The sealing bar protection device was activated. Restore the sealing bar protection device by pressing the key to restore protection. If the fault recurs contact the Technical Support Service. * The sealing bar is broken. Contact the Technical Support Service.
What to do if Orved Evox 31 Hi-Line displays 'COOL DOWN PRODUCT OR DECREASE LIQUID PART'?
If the display shows 'COOL DOWN PRODUCT OR DECREASE LIQUID PART' accompanied by an audible signal at the end of the cycle, it means the product is either too wet or too hot. If necessary, repeat the cycle by cooling the product or by inserting a lesser quantity of product or liquid.
What to do if Orved Evox 31 Hi-Line Kitchen Appliances displays 'NO GAS FLUSH' during a cycle?
If the display shows 'NO GAS FLUSH' accompanied by an audible signal during a cycle, check the following: * The gas bottle might be empty, closed, or not connected. Change, open, or connect the gas bottle. * The gas bottle connection pipe might be pressed. Replace the connection pipe. * The gas solenoid valve might be faulty. Call an authorized service centre.
What to do if Orved Evox 31 Hi-Line displays 'VACUUM NOT STARTED' during a cycle with external container?
If the display shows 'VACUUM NOT STARTED' accompanied by an audible signal during a cycle with an external container, it could be due to: * The lid of the external container is not positioned correctly. Correctly position the lid of the external container. * The external suction device was not properly connected. Correctly connect the external suction device to the packaging machine and to the container.
Why my Orved Evox 31 Hi-Line Kitchen Appliances packaging machine does not switch on?
The packaging machine might not be getting power because: * The machine is not powered. Check the power supply to the socket being used. * The power plug is not properly inserted. Insert the power plug into the socket.
Why is my Orved Kitchen Appliances packaging machine off?
The packaging machine might be off due to: * No electrical power. Disconnect the electrical power supply. * An electronic fault. Contact the Technical Support Service.
What to do if too much air remains in the sealed bag with Orved Evox 31 Hi-Line?
If too much air remains in the sealed bag, consider the following: * The bag may not be the right size for the product. Use a suitably sized bag. * The vacuum level selected may be too low. Repeat the cycle with a higher vacuum level. * If the product is liquid, it is normal for some air bubbles to remain inside.
Specifies the correct and intended use of the appliance, excluding improper applications.
Covers electrical safety, grounding, authorized repairs, and potential hazards from damaged components.
Provides guidelines for proper operation, including temperature hazards, material compatibility, and usage restrictions.
Details the procedure for vacuum packaging items using containers placed directly inside the chamber.
Explains how to use external containers with the packaging machine via an accessory.
Explains the pump oil dehumidification cycle to remove moisture from the vacuum pump.
Provides instructions for manually initiating and completing the pump oil dehumidification cycle.
Essential safety guidelines that must be followed during the installation process.
Step-by-step procedure for installing the packaging machine in its operating environment.
General| Category | Kitchen Appliances |
|---|---|
| Model | Evox 31 Hi-Line |
| Brand | Orved |
| Sealing bar length | 310 mm |
| External dimensions | 360x510x440 mm |
| Voltage | 230 V |
| Energy Efficiency Class | Not applicable |
| Capacity | Not applicable |
| Number of Cooking Levels | Not applicable |
| Power Supply | Electric |
| Power Consumption | 0.45 kW |
| Dimensions (WxDxH) | 360x510x440 mm |
| Material | Stainless steel |
| Color | Stainless steel |
| Control Type | Digital |
| Temperature Range | Not applicable |
| Timer | Yes |
To Next Page