Panasonic AU-EVA1 - Page 90

90
6-5. Troubleshoot (INVALID error message)
Following tables show major causes and ways to cope with “INVALID” error message.
When occurred?
Cause
Remedy
Pressed a user button,
SLOT SEL function
assigned.
SD card being mounted is just one.
Need two cards to perform SLOT
SEL.
Mount one more SD card.
SIMUL record mode is being turned
ON.
REC CHECK function does not work while SIMUL mode is
working.
Set REC SETTINGS > 2 SLOTS FUNC. > RELAY REC to
cancel the SIMUL mode.
The card to be moved is not
recordable.
Mount recordable SD card.
The EVA1 is currently recording (on
built-in recorder and/or external
recorder connected via SDI, HDMI.
The function cannot be turned ON/OFF while recording. Stop
recording and try again.
PRE REC is under ON (or OFF)
process.
Wait until the change process finishes.
SDI RAW output mode is being
turned ON.
Set SYSTEM SETTINGS > SYSTEM MODE >SDI RAW > OFF
Called center marker
or frame marker.
FOCUS SQUARE focus assist is
being turned ON.
Turn OFF the function with the USER button SQUARES F.A.
assigned.
EXPAND focus assist I being turned
ON.
Turn OFF the function with the USER button EXPAND
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
LCD CLEAN VIEW is being turned
ON.
Turn OFF the function with the USER button LCD CLEAN
VIEW assigned.
Pressed a user button,
SPOT METER
function assigned.
EXPAND focus assist I being turned
ON.
Turn OFF the function with the USER button EXPAND
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
Pressed a user button,
LEVEL GAUGE
function assigned.
EXPAND focus assist I being turned
ON.
Turn OFF the function with the USER button EXPAND
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
LCD CLEAN VIEW is being turned
ON.
Turn OFF the function with the USER button LCD CLEAN
VIEW assigned.
Pressed a user button,
Waveform monitor
display function
assigned.
FOCUS SQUARE focus assist is
being turned ON.
Turn OFF the function with the USER button SQUARES F.A.
assigned.
EXPAND focus assist I being turned
ON.
Turn OFF the function with the USER button EXPAND
assigned.
LCD CLEAN VIEW is being turned
ON.
Turn OFF the function with the USER button LCD CLEAN
VIEW assigned.
Pressed a user button,
ZEBRA indicator
assigned.
FOCUS SQUARE focus assist is
being turned ON.
Turn OFF the function with the USER button SQUARES F.A.
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
Pressed a user button,
PEAKING focus assist
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
Pressed a user button,
FOCUS SQUARE
focus assist assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
Pressed a user button,
EXPAND (Image
magnification) focus
assist assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
Pressed a user button,
LEVEL GAUGE SET
(setting of current
horizontal and vertical
position as the
reference point for the
level gauge) assigned.
LEVEL GAUGE is not yet turned ON
Turn ON the function with USER button LEVEL GAUGE
assigned or set OUTPUT SETTINGS > LCD LEVEL GAUGE >
LEVELGAUGE > ON.
EXPAND focus assist I being turned
ON.
Turn OFF the function with the USER button EXPAND
assigned.
COLOR BARS is being turned ON.
Turn OFF "COLOR BARS" with a user button.
LCD CLEAN VIEW is being turned
ON.
Turn OFF the function with the USER button LCD CLEAN
VIEW assigned.
6. Appendix