Panasonic AW-UE150KP

HDMI
Make the settings for output from the HDMI connector.
Format
Set the output format.
The following format settings are possible depending on the [Format]
setting in the [System] screen.
Frequency System Format Format (HDMI)
59.94Hz 2160/59.94p 2160/59.94p
1080/59.94p
*
2
2160/29.97p 2160/29.97p
1080/29.97p
1080/59.94p 1080/59.94p
1080/59.94i 1080/59.94i
1080/29.97p 1080/29.97p
1080/29.97PsF 1080/29.97p
1080/23.98p(59.94i)
*
1
1080/23.98p(59.94p)
*
3
720/59.94p 720/59.94p
50Hz 2160/50p 2160/50p
1080/50p
*
4
2160/25p 2160/25p
1080/25p
1080/50p 1080/50p
1080/50i 1080/50i
1080/25p 1080/25p
1080/25PsF 1080/25p
720/50p 720/50p
24Hz 2160/24p 2160/24p
1080/24p
1080/24p 1080/24p
23.98Hz 2160/23.98p 2160/23.98p
1080/23.98p
1080/23.98p 1080/23.98p
1080/23.98PsF 1080/23.98p
*
1
It denotes “1080/23.98p over 59.94i”.
*
2
When [Crop Mode] is [Crop(720)], output is 720/59.94p.
*
3
It denotes “1080/23.98p over 59.94p”.
*
4
When [Crop Mode] is [Crop(720)], output is 720/50p.
Factory settings: 2160/59.94p (AW-UE150WP/AW-UE150KP)
2160/50p (AW-UE150WE/AW-UE150KE)
HDR Output Select [SDR, HDR(2020), HDR(709)]
Select the signal to be output when [Gamma Mode] is [HLG].
SDR SDR output
HDR(2020) HDR output (BT.2020 equivalent color gamut)
HDR(709) HDR output (BT.709 equivalent color gamut)
Factory settings: HDR(2020)
<NOTE>
• Other than when [Gamma Mode] is [HLG], [Color Setting] is
[Normal], and [Video Sampling] is [4:2:2/10bit], [HDR Output Select]
cannot be changed. (→ page 97, page 120)
V-Log Output Select [V-Log, V-709]
Select the signal to be output when [Color Setting] is [V-Log].
V-Log Output with a gamma curve that has a wide range of
tones and latitude (exposure range).
V-709 Converted for output to images suited to previewing.
Factory settings: V-Log
<NOTE>
• [V-Log Output Select] cannot be changed when [Color Setting] is
not [V‑Log]. (→ page 97)
Video Sampling [4:2:2/10bit, 4:2:0/8bit]
When [Format] in [HDMI] is [2160/59.94p] or [2160/50p], select the
video sampling output from the HDMI connector.
4:2:2/10bit Output in 4:2:2/10bit mode.
4:2:0/8bit Output in 4:2:0/8bit mode.
Factory settings: 4:2:2/10bit
<NOTE>
• When [Format] in [HDMI] is other than [2160/59.94p] or [2160/50p],
[Video Sampling] cannot be changed and is fixed at [4:2:2/10bit].
Bar [Camera, Colorbar]
Switch between camera images and color bars.
Camera Camera images
Colorbar Color bar
Factory settings: Camera
Color Bar Type [Type1, Type2]
Select the type of color bar to display.
Type1:
Type2:
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Type2
<NOTE>
• Even if the [HDR Output Select] for each of the outputs is either
[HDR(2020)] or [HDR(709)], the color bar for SDR is output.
Tone [Off, Low, Normal]
Make the settings for the test tone signal (1 kHz) output while the
color bar is displayed.
Off Test tone is not output.
Low Test tone is output at low volume.
Normal Test tone is output at normal volume.
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Normal
OSD Mix
Select whether to turn off/on camera menu, status, and other displays
for each output image.
12G SDI/OPTICAL [Off
*
, On]
3G SDI [Off
*
, On]
MONI [Off, On
*
]
HDMI [Off
*
, On]
IP [Off, On
*
]
Off
The camera menus and statuses are not displayed on the
output pictures covered by the setting items listed above.
On
The camera menus and statuses are displayed for the output
pictures covered by the setting items listed above.
*
: Factory settings
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
100 101
Web screen configurations (continued)