To Next PageTo Next PageWhy are the images distorted on my Panasonic AW-UE150WE?
If the images from your Panasonic Security Camera appear distorted, it could be due to congestion on the transmission path, preventing proper transmission. Also, distortion can occur if video packet shuffling happens during transmission.
How to troubleshoot a Panasonic Security Camera with no power?
If your Panasonic Security Camera is not powering on, ensure the AC cable of the external DC power supply is securely connected to the AC outlet and that the power plug of the external DC power supply is properly connected. Also, verify that the LAN cable is securely connected to the LAN connector for IP control, and that the network cable for the PoE++ compatible power supply device is properly connected. Power may not be supplied if the total power limit is exceeded on power supply devices. Check the connection to the controller, if applicable, and ensure proper operation when using a wireless remote control.
What to do if the status display lamp does not light on Panasonic AW-UE150WE Security Camera?
If your Panasonic Security Camera's status display lamp isn't lighting up, it might be because the [Status Lamp] setting is set to [Disable]. To resolve this, change the setting to [Enable].
Why can't I operate my Panasonic AW-UE150WE Security Camera with the remote control?
If you cannot operate your Panasonic Security Camera using the wireless remote control, ensure the batteries haven't run down or been installed with reversed polarities. If the status display lamp doesn't blink when operating the remote near the signal light-sensing area, replace the batteries. Also, check if the IR ID switches are correctly set. Finally, consider whether a nearby fluorescent light or plasma monitor is interfering with the wireless remote control signal.
What to do if I cannot operate Panasonic Security Camera using the controller?
If you cannot operate your Panasonic Security Camera using the controller, verify that the unit is properly connected to the controller. It may also be necessary to upgrade the controller's version to ensure it supports the unit.
Why won't my Panasonic AW-UE150WE operate with the remote or controller?
If you're experiencing issues operating your Panasonic Security Camera with either the wireless remote control or the controller, first ensure the power is on. If the status display lamp is off or lights up orange, the unit's power is not on. Also, check if the safe mode function has been activated, or if limiter functions have been set. Finally, make sure the unit you intend to operate has been properly selected.
Why does the authentication screen appear repeatedly on my Panasonic AW-UE150WE?
If the authentication screen appears repeatedly on your Panasonic Security Camera, it might be because the user name or password has been changed. Close the web browser and initiate access to the unit again. Alternatively, the method for user authentication might have been changed. In this case, close the web browser and initiate access again.
What to do if no pictures are displayed on Panasonic Security Camera?
If no pictures are displayed or the pictures are disturbed on your Panasonic Security Camera, first check if the unit has been properly connected to the other connected devices. Also, confirm that the correct unit has been selected if the system is configured to switch the picture when the unit to be operated is selected. Ensure that the image signal setting has been correctly selected and that external sync signals supported by the video signal format are being input.
Why don't the tally lamps light on my Panasonic AW-UE150WE Security Camera?
If the tally lamps on your Panasonic Security Camera do not light, check if the [Tally] setting is set to [Disable]. If it is, change the setting to [Enable].
General| Type | IP security camera |
|---|---|
| PTZ control | Yes |
| Placement supported | Indoor |
| Connectivity technology | Wired |
| Form factor | Bullet |
| Mounting type | Ceiling/wall |
| Product color | White |
| Pan range | -175 - 175 ° |
| White balance | ATW, Auto, Manual |
| Tilt angle range | -30 - 210 ° |
| Camera shutter type | Electronic |
| Camera shutter speed | 1/24, 1/25, 1/30, 1/48, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/10000 s |
| Minimum illumination | 2 lx |
| Sensor type | MOS |
| Number of sensors | 1 |
| Focus | Motorized/Manual |
| Digital zoom | 10 x |
| Optical zoom | 20 x |
| Focal length range | 8.8 - 176 mm |
| Maximum aperture number | 4.5 |
| Minimum aperture number | 2.8 |
| Closest focusing distance | 0.1 m |
| Total megapixels | - MP |
| Maximum resolution | 3840 x 2160 pixels |
| Supported video modes | 720p, 1080p, 2160p |
| Video compression formats | H.264, H.265, M-JPEG |
| Supported graphics resolutions | 320 x 180, 640 x 360, 1280 x 720 (HD 720), 1920 x 1080 (HD 1080), 3840 x 2160 |
| Sample rate | 48 kHz |
| Audio formats supported | AAC |
| Signal-to-Noise Ratio (SNR) | 60 dB |
| Wi-Fi | No |
| Streaming method | Multicast, Unicast |
| Networking standards | IEEE 802.3bt |
| Supported network protocols | IPv4, IPv6, TCP / IP, UDP / IP, HTTP, HTTPS, RTSP, RTP / RTCP, DHCP, DNS, DDNS, NTP, UPnP, IGMP, ICMP, ARP, RTMP |
| BNC output ports | 3 |
| DC output voltage | 12 |
| Power source type | DC, PoE |
| Storage temperature (T-T) | -20 - 50 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Mac operating systems supported | Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.13 High Sierra |
| Mobile operating systems supported | iOS 11.0 |
| Windows operating systems supported | Windows 10, Windows 7 |
Weight and Dimensions| Depth | 219 mm |
|---|---|
| Width | 213 mm |
| Height | 267 mm |
| Weight | 4200 g |
Crucial safety information and warnings for users before starting the installation process.
Key advice on proper installation procedures, environmental considerations, and safety.
Configuration of IR ID and service switches before mounting the unit.
Step-by-step guide for physically mounting and connecting the camera, including accessory usage.
Procedures for installing the unit on a desktop or tripod when not suspended.
Diagrams illustrating how to connect the camera to various systems like switchers and controllers.
Visual guide to the external components and dimensions of the camera unit.
Essential safety information and warnings for users operating the camera unit.
Covers overview, computer requirements, network security, and warranty disclaimer.
Overview of the camera's advanced features, including zoom, night mode, and connectivity.
Guidelines for optimal camera performance, environmental use, and maintenance.
Instructions on how to operate the camera using the optional wireless remote control.
Detailed explanation of all connectors, indicators, and functional parts of the camera unit.
Steps to set up remote control IDs for managing multiple camera units.
Guide to setting up network parameters, IP addresses, and initial user accounts.
How to properly turn the camera unit on and off using remote controls or controllers.
Solutions for common operational issues, image problems, and system errors.
