21
RQT6986
Playing back
[HDD] [RAM] [DVD-R]
Play restarts from approximately a minute later. Convenient when
you want to skip commercials etc.
During play
Press [CM SKIP].
[Note]
If the start of the next program is within one minute of the point you
skipped from, play restarts from the beginning of that program.
[HDD] [RAM] [DVD-R]
1 During play
Press [TIME SLIP].
2 Within 5 seconds
Press [3, 4] to enter the time and
then press [ENTER].
Press to alter in one-minute units. Press and hold to alter in
10-minute units.
[HDD] [RAM] (Only with Dolby Digital)
You can increase the speed of play without disrupting the
soundtrack.
During play
Press and hold [1] (PLAY/
k
1.3).
To return to normal speed
Press [1] (PLAY/
k
1.3).
[Note]
≥Output is in PCM when using a digital connection (➜page 59, [A]).
≥This is canceled when you perform skip, pause or when play
reaches a point where a program recorded in sound other than
Dolby Digital starts.
≥This does not work if the setting is “Off” in “PLAY
k
1.3 & Audio
during Search” (➜page 52).
≥This does not work when recording in XP or FR mode. [RAM]
You can mark positions by pressing [MARKER]. Also use on-screen
menus to mark, recall, and clear positions.
[HDD] [RAM] [DVD-R]
Mark up to 999 positions. The unit records the markers directly onto
the disc and they remain intact even if you remove the disc.
[DVD-A] [DVD-V] [VCD] [CD] [MP3]
Mark up to 5 positions. The markers clear when you open the disc tray.
During play
Press [MARKER].
One marker is added.
1 During play
Press [DISPLAY].
The on-screen menus appear.
2 Press [3, 4] to select “Play” and
press [1].
e.g., DVD-RAM
3 Press [3, 4] to select “Marker” and
press [1] to highlight the first aster-
isk (¢).
[HDD] [RAM] [DVD-R] [DVD-A] [DVD-V] [VCD] [CD] [MP3]
4 Press [2, 1] to select an asterisk (¢)
and press [ENTER].
One marker is added.
To recall a marker
Press [2, 1] to select a marker number and press [ENTER].
≥Play starts from the marked position.
To clear markers
Press [2, 1] to select a marker number and press [CANCEL].
≥An asterisk replaces the number and the position is cleared.
To clear the on-screen menus
Press [RETURN].
Skipping a minute forward—CM Skip
Selecting an amount of time to skip
—Time Slip
Quick View
0 min
–5 min
e.g., Go back to 5 minutes
L R
PLAY
HDD
L R
PLAY t1.3
HDD
Marking places to play again—MARKER
Marking positions directly
Using on-screen menus to mark positions
When marking positions 11 and above
[HDD] [RAM] [DVD-R]
1 Press [2, 1] to highlight “1–10”.
2 Press [3, 4] to select “11–20”.
You can select the next group of 10 when the current group is full.
3 Press [1].
The first asterisk is highlighted.
4 Press [ENTER] to mark a position.
[Note]
≥You cannot use this feature if:
– the disc’s elapsed play time is not shown in the display.
– you are using a play list. [HDD] [RAM]
– protection (cartridge ➜page 10, disc ➜page 44) is set (you
can still recall the markers to play a position). [RAM]
≥Subtitles around markers may fail to appear.
≥Markers are cleared when you finalize DVD-R (➜page 44).
≥
Markers on HDD, DVD-RAM and DVD-R are ordered by time, so
marker numbers can change when you add and delete them.
Disc
Video
Audio
OFF
1s10
††††††††††
Marker
Play
Repeat play
1s10
††††††††††
†††††
1
1s10
To Next Page
Loading...
