7
Code table
Use this function to copy the settings of a master sensor to a slave sensor.
Procedure, set copy function
1 Set the master sensor to 'Copy ON' or 'Copy ON-L'. Press so that
the sensor is in the copy ready state. For details, see page 6, section 11,
PRO MODE.
2 Turn off the master sensor.
3 Connect the master and slave sensors as shown.
4 Turn on the master sensor and the slave sensor at the same time.
1,
2
5 The master’s contents (16-bit coded) are shown in orange on its main
display and copying starts.
The same code appears in green on the slave’s main display, and OK
appears on the sub-display when copying is complete.
6 Turn off the power of the master side sensor and the slave side sensor
and disconnect the wire.
To copy settings to another sensor, repeat steps 3 to 6.
Procedure, cancel copy function
1 While the slave sensor is disconnected, turn on the power of the master
sensor.
2 Press for approx. 2s.
The auto-reference function corrects the setting value using the detected
pressure value during auto-reference input as the reference pressure.
Using the detected pressure value at auto-reference input P(a) as a refer-
ence, the set value 1’ is automatically corrected to “set value 1 + P(a)”.
Operation charts
The detected pressure value at auto-reference input becomes “zero”
when the setting of the analog voltage output / external input function is
changed or the power is turned ON again.
The auto-reference input value can be checked when setting the
threshold value in RUN mode. For details, see page 3, section 9, RUN
MODE.
12 SETTING COPY FUNCTION
Notes: • The master and slave must be identical models.
• You can only copy settings to one slave at a time.
1
If the power is not turned on at the same time, the setting contents may not be
copied.
2
When the power is on, pulse output is output to comparative output 1.
㧙㧙㧙㧙 㧙㧙
㧙㧙 㧙㧙
㧙
㧙
㧙
㧙
P-1, Lo-1
Hi-1
P-2, Lo-2
Hi-2
ADJ.
MPa 250ms
5ms kPa 500ms
10ms kgf/cm
2
1000ms
25ms bar
㧙㧙
50ms psi
㧙㧙
100ms mmHg
㧙㧙
250ms inchHg
㧙㧙
500ms
㧙㧙㧙
1000ms
㧙㧙㧙
5000ms
㧙㧙㧙
Code
OFF
Std
Full
Response time Unit selection Display speed ECO mode
Fifth digit 6th digit 7th digit 8th digit
Analog
voltage output
Compara-
tive output 1
Compara-
tive output 1
Compara-
tive output 1
Compara-
tive output 1
Compara-
tive output 2
Compara-
tive output 2
Compara-
tive output 2
Compara-
tive output 2
Remote
zero-adjustment
Auto
reference
N.O. OFFOFF
N.C. N.O.
N.O. N.C.
N.C.
N.O.
N.O.
N.C.
N.C.
N.C.
N.O.
EASY
Hysteresis
Window
comparator
EASY
Hysteresis
Window
comparator
Red when
ON
Green when
ON
Always red
Always green
1st digit
N.O. / N.C.
selection
Comparative
output 1 mode
Comparative
output 2 mode
N.O. / N.C.
selection
Analog volt. output/
external input
Threshold
display
Main display
color
Display color
based on:
2nd digit
Standard type
High-
function
type
Standard
type only
3rd digit
4th digit
Code
2.5ms
MODE
*For the high-function type, analog voltage / external input.
(Brown) +V (Brown) +V
(Blue) 0V (Blue) 0V
(Black) Comparative output 1 (Black) Comparative output 1
(White) Comparative output 2* (White) Comparative output 2*
Master Slave
Power supply
Color code of cable with connector
13 AUTO-REFERENCE FUNCTION
Notes: • The pressure range that can be set is wider than the rated
pressure range so that the auto-reference function can be
handled.
• If the corrected setting value exceeds the set pressure range
when auto-reference input is carried out, the setting value will
be automatically corrected to fall within the set pressure
range. Thus, take care not to exceed the set pressure range.
During normal operation. (Each
comparative output set to N.O.)
During remote zero-adjustment
input. (Each comparative out-
put set to N.O.)
• Detected pressure at auto-
reference input: 10kPa
• Output mode: Hysteresis mode
Note: The setting values shift in the same manner during EASY mode
or the window comparator mode.
MODE
SV 1
SV 1’
P(a)
1’ = 1 + P(a)
Pressure
Atmospheric pressure
ON
OFF
ON
OFF
SV (set value) 1’ after auto-reference is:
Before auto-reference
After auto-reference
Detected pressure value
at auto-reference input
10 20 30 40 50 60
0
10 20 30 40 50 60
0
1
10 20
10 20 30 40 50 60
0
10 20 30 40 50 60
0
P(a)
10
20 30
2
1’ 2’
ON
OFF
Output
Applied pressure (kPa)
Displayed value (kPa)
Set value (kPa)
ON
OFF
Output
Applied pressure (kPa)
Displayed value (kPa)
Set value (kPa)
Rugghölzli 2
CH - 5453 Busslingen
Tel. +41 (0)56 222 38 18
Fax +41 (0)56 222 10 12
mailbox@sentronic.com
www.sentronic.com
Produkte, Support und Service
SEN
TRONIC
AG
To Next Page
Loading...
