Panasonic KX-FT37 Series

1 REPLACEMENT PARTS LISTS
1.1. REFERENCE CHART
Reason for Change
*The following items (1-8) indicate the reason for change. See the “Notes” column for each part in 1.2. ORIGINAL AND NEW PARTS
COMPARISON LIST(S).
1. Improve performance Remarks:
2. Change of material or dimension *a: To improve the electric conduction.
3. To meet approved specification *b: For prevention of static electricity.
4. Standardization *c: To facilitate the production process.
5. Addition *d: To share the part with other models.
6. Deletion *e: To meet the Argentine safety requirements.
7. Correction *f: To modify the parameter for inspection on the production line.
8. Other *g: The factory for production is transferred from Japan to China. (The place of production described
in the name plate is changed from “Made in Japan” to “Made in China”.)
*h: To improve the tone quality of TAM.
*i: To improve cutter’s performance
Interchangeability Code
**The following items (V-Z) indicate the interchangeability. See the “Notes” column for each part in 1.2. ORIGINAL AND NEW PARTS
COMPARISON LIST(S).
Parts Set Production
V Original
New
Early (before change)
Late (after change)
Original or new parts may be used in early or late production set.
Use original parts until exhausted, then stock new parts.
W Original
New
Early (before change)
Late (after change)
Original parts may be used in early production sets only. New parts may be used in early or
late production sets. Use original parts where possible, then stock new parts.
X Original
New
Early (before change)
Late (after change)
New parts only may be used in early or late production sets.
Stock new parts.
Y Original
New
Early (before change)
Late (after change)
Original parts may be used in early production sets only. New parts may be used in late
production sets only. Stock both original and new parts.
Z Other
Note:
Alphabets in the “Remarks” column in the following lists correspond to the alphabets in the “Remarks”in1.1. REFERENCE
CHART.
1.2. ORIGINAL AND NEW PARTS COMPARISON LIST(S)
1.2.1. KX-FT31BX, KX-FT31BX-W
Ref No. Part No. Part Name & Descriptions Pcs/
Set
Remarks Notes
Original Part No. New Part No.
CABINET AND ELECTRICAL SECTION
25 PFUS1095Z PFUS1095X OPEN EARTH 1 *a 1 W
37 PFMH1046Z PFMH1046Y SHADING PLATE 1 *b 1 W
104 PFAS50PTC01Y PFWE1FT31BX SPEAKER ASS’Y (See 4.2. LOWER
CABINET / P.C.B. SECTION.)
1 *d 4 Y
104-1 --------------------------- PFUS1165Z SPRING, SPEAKER 1 *d 4 Y
106 PFUS1089Z --------------------------- ----------------------------------------- 0 Deleted --- ---
ACCESSORIES AND PACKING MATERIALS
P1 PFPK1320Z PFPK1476Z-J GIFT BOX (KX-FT31BX only) 1 *c 8 V
P1 PFPK1352Z PFPK1477Z-J GIFT BOX (KX-FT31BX-W only) 1 *c 8 V
FIXTURES AND TOOLS
EC5 PQZZ2K6Z PFZZ12K1Z CONNECTOR, 12PINS 1 -------- 7 ---
EC9 PFZZ12K1Z PQZZ12K4Z CONNECTOR, 12PINS 1 -------- 7 ---
1.2.2. KX-FT31CX-W
Ref No. Part No. Part Name & Descriptions Pcs/
Set
Remarks Notes
Original Part No. New Part No.
CABINET AND ELECTRICAL SECTION
25 PFUS1095Z PFUS1095X OPEN EARTH 1 *a 1 W
FIXTURES AND TOOLS
EC9 PFZZ12K1Z PQZZ12K4Z CONNECTOR, 12PINS 1 -------- 7 ---
2
KX-FT31 Series / KX-FT33 Series / KX-FT37 Series